Stimmen - 4, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
Use the equipment only as described and for the indicated purposes. By doing this you will be able to work in complete safety and produce better results. We hope you enjoy using your planer. FEATURES OF THE PEH 900 Guide handle / planing depth adjuster Dust outlet Vee groove Planing depth scale Base plate ON/OFF switch Cutting block / planer blades Drive interrupt Safety cover Side fence Dust channel Toothed belt cover Rebating depth stop TECHNICAL INFORMATION Nominal power: 900 W Nominal voltage: 230 V ~ 50 Hz Weight: 3,6 kg No load speed: no 11,000 rpm Sound pressure level: 87 dB (A) Planing depth: 0 - 3.5 mm Sound power level: 100 dB (A) Rebating depth: 0 - 24.0 mm Vibration: 2,5 m/s2 (hand-arm vibration) Planing width: 82 mm Protection class: II / . IMPORTANT SAFETY ADVICE To be read in conjunction with the advice in the accompanying booklet on safety before using for the first time. The PEH 900 power planer is intended to be used for planing wood (e.g. beams, boards). . If the mains cable is damaged or cut through during the work - never touch the cable - pull out the mains plug immediately. Never use electri cal equipment with damaged cables. . For operating the planer for longer periods and particularly if dust that may be hazardous to heath is created, the planer should be connected to a suitable external vacuum device. Wear a dust mask. Make sure you only use sharp blades. Always keep the power cable fed to the rear of the machine. Never plane over metal objects, nails or screws. 8 Only place the planer against the workpiece after switching it on. The base plate must always lay flat on the workpiece when working. Do not clear dust etc. from the dust outlet with your fingers. Use a piece of wood to dislodge any trapped planing debris. OPERATION The PEH 900 power planer has INTELLIGENT POWER CONTROL. This electronic management system monitors and controls your power planer in its various operating states; Operating state Feature Switching On/Off: The IPC electronic system start-up mode ensures that the motor starts up slowly and gently. This large ly avoids heavy transient current surges, and means that electrical safety cut-out devices are not generally tripped (building sites, domestic premises). No-load running: After switching on, the IPC electronic management system run-up mode takes the planer speed up to the pre-set required value. After this is reached, the IPC system speed control mode keeps the grinder operating at a constant speed. . WARNING: Always remove the plug from the mains socket before working on the planer. Take note of the mains voltage. The voltage must agree with that shown on the rating plate (equipment shown as 230 V can also be used with 220 V). ON / OFF SWITCH . On the grounds of safety the ON / OFF switch cannot be locked in the ON position for continuous operation. It must always be pressed during operation. SETTING THE PLANING DEPTH The planing depth can be set between 0 - 3.5 mm. Turn the guide handle/ planing depth adjuster and set the pointer to the desired mark or value. DUST REMOVAL AND VACUUM EXTRACTION The dust outlet can simply be switched to the right or left by fitting the cap over the appropriate opening. 9 OPERATING INSTRUCTIONS Always switch on the planer before making contact with the material and then guide the planer on to the workpiece PLANING SURFACES Place the planer with the front of the base plate on the workpiece. Always make sure when you are planing surfaces such as beams and boards that the base plate is in full contact with the surface to avoid the danger of blade kickback. Always use both hands to guide the plane over the workpiece with even forward pressure. CHAMFERING CORNERS The vee groove in the centre of the front of the base plate allows you to chamfer the corners of your workpiece very quickly and easily. Place the planer on to the workpiece with the vee groove on the corner and then guide the planer along the corner. Make sure you keep the angle at 45° and an even forward pressure. REBATING Example set up: for right hand rebates the side fence goes on the left and the rebating depth stop goes on the right into the holes on the planer (with the planer viewed from above). Set the rebating depth up to a max. 24 mm using the rebating depth stop . Set the side fence to give the required width. Adjust the pla ning depth scale to the maximum of 3.5 mm. Go over the workpiece as many times as is required to obtain the desired rebate. CHANGING OR REVERSING THE PLANER BLADES WARNING: Before doing any work on the planer always pull out the plug from the mains. . IMPORTANT ADVICE: Do not unscrew the two hexagonal socket headed screws. They adjust the height of the cutting block. Adjustment is only required if you wish to change to another planer blade type e.g. a profiled blade. HSS reversible blades are fitted as standard at the works. When you change blades, always change both blades to avoid any imbalance. When ...