Login:
Stimmen - 3, Durchschnittliche Bewertung: 4.7 ( )

Anleitung SEH Computertechnik, modell IC146-ETHER-HP-FL

Hersteller: SEH Computertechnik
Dateigröße: 209.6 kb
Dateiname: 1c2f3023-60bf-4fe7-b4ca-37ba41aeba70.pdf
Unterrichtssprache:enes
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


Qieghed l-ghotjien protettivi fuq il-konnettur SC jew ST jekk inti mhux ser tuzah. • Il-print server huwa mahsub biex jigi installat fil-printer u m'ghandux jigi uzat fuq barra. Hardware Installation Guide 11 ! Print Server Controls and Technical Data 1) Network activity LED (yellow): The LED lights up when data packets are being received. 2) TX 3) RX 4) Link indicator LED (green): The LED lights up when a (physical) connection to the network is availably. 5) Status button 6) Status indicator LED (green): The LED shows that the print server is operational. Characteristics Values Printer Connector - HP EIO Network Connection logical: - IEEE 802.3j (10BaseFL Ethernet) physical: - ST (Type MMF 62,5/125) Operating Environment - Ambient temperature: 5 - 40 °C - Relative humidity: 20 - 80 % Dimensions - Length 135 mm - Width 90 mm - Height 32 mm - Weight 85 g 12 Hardware Installation Guide i Mounting the Print Server The print server is a so-called slot card that is simply inserted into the foreseen slot. The print server slot is usually located next to, or above the printer's Centronics interface. Insert the print server tc Proceed as follows: 1. Turn the printer off. 2. Disconnect the printer's power cord. 3. Remove the data cable connecting the printer to the computer. 4. Remove the screws from the interface cover. 5. Remove the metal cover. 6. Insert the print server board into the slot until the board locks into the receptacle. 7. Fasten the print server board screws. Connect the print server tc Proceed as follows: 1. Connect the network cable to the print server. 2. Connect the printer's power cord to the printer. 3. Turn the printer on. 4. Press the status button of the print server in order to print out a status page. Hardware Installation Guide 13 ! Notification Manufacturer's Name: SEH Computertechnik GmbH Manufacturer s Address: Suedring 11 33647 Bielefeld Germany Computertechnik GmbH EC - Declaration of Conformity Product: Built-In Print Server Type designation: IC146 - ETHER-HP-FL The designated product is in conformity with the European Directive 89 / 336 / EEC "COUNCIL DIRECTIVE of 3 May 1989 on the approximation of the laws of the Member States relating to electromagnetic compatibility" Full compliance with the standards listed below proves the conformity of the designated products with the provisions of the EC-Directive 89/ 336/ EEC: EN 55024:1998 EN 55022:1998 /A1:2000 Class B The instructions in the enclosed manual Hardware Installation Guide have to be kept completely to meet the above specifications. Bielefeld, December 4< 2001 Dipl.-lng. Rainer Ellerbrake, General Manager 14 Hardware Installation Guide Federal Communication Commission (FCC) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Pursuant to Part 15.21 of the FCC Rules, any changes or modifications to this device not expressly approved by the SEH Computertechnik GmbH may cause interference and void the FCC authorization to operate this device. This device has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against interference in a commercial environment. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause interference to radio communications. Installing this device ...


Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien