Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
:/i "< i . '_,/,_ __ _ i_: _i, _ ,///i ...... • ', MODEL NO. ]]3.20680 JOINTER/PLANER ONLY 113.206930 JOINTER!PLANER WITH LEGS AND MOTOR Serial Number ....................................... Model and serial number may be found on a plate attached to your infeed table. You should record both model and serial number in a safe place for future use. CAUTION: Read GENERAL and ADDiTiONAL SAFETY iNSTRUCTiONS carefully CRn MaNo 6_-INCH JOIN TER-PLANER ® assembly ® operating o repair parts Sotd by SEARS, ROEBUCK. AND CO., Chicago, _t. 60684 U.S.A. PartNo.67036 :..........' : : ::': FULL ONEYEAR WARRANTY ON CRAFTSMAN JOINTER/PLANER year from the date of purchase, this Craftsman Jointer/Planer fails due to a defect in material rs will repair it, free of charge. ,VAtLABLE BY SIMPLY CONTACTING THE NEAREST SEARS STORE THROUGHOUT THE UNITED STATES. you may also have other rights which vary from state to SEARS, CO,; Sears Tower, BSC 41-3. Chicago. IL 60684 general safety instructions for power fools 1.:KNOW YOUR POWER TOOL 13. SECURE WORK Read the owner's manual carefully. Learn its Use clamps or a vise to hold work when practical It's application and limitations as well as the specific safer than using your hand, frees both hands to operate tool. potential hazards peculiar to this tool. 14. DON'T OVERREACH 2.:GROUND ALL TOOLS This tool is equipped with an approved 3.conductor Keep proper footing and balance at all times, c0rd and a 3-prong grounding type plug to fit the 15. MAINTAIN TOOLS WITH CARE proper grounding type receptacle The green conductor in the cord is the grounding wire. Never connect the Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and green wire to a live terminal. changing accessories. 3; KEEP GUARDS IN PLACE in working order, and in proper adjustment and 16. DISCONNECT TOOLS alignment, before servicing; when changing accessories such as 4. REMOVE ADJUSTING KEYS blades, bits, cutters, etc. AND WRENCHES 17. AVOID ACCIDENTAL STARTING Form habit of checking to see that keys and adjusting Make sure switch is in "OFF" position before pluggingwrenches are removed from tool before turning it on. in, 5: KEEP WORK AREA CLEAN 18. USE RECOMMENDED ACCESSORIES Cluttered areas and benches invite accidents. Floor Consult the owner's manual for recommended must not be Slippery due to wax or sawdust. accessories, Fol}ow the instructions that accompany6;:!AV01D DANGEROUS ENVIRONMENT the accessories. The use of improper accessories may D0n't use power tools in damp or wet locations or cause hazards. expose them to rain; Keep work area well lighted; 19: NEVER STAND ON TOOL Provide adequate surrounding work space. i: i ::":i Seri0us injury could occur if the toot is tipped or if the 7. KEEP CHILDREN AWAY cuttin. tool is accidentally contacted. All visitors-should be kept a safe distance from work DO not store materials above or near the tool such that area. it is necessary to stand on the too_ to reach them. 8. MAKE WORKSHOP KID-PROOF -- with padlocks, master switches, or by removing 20. CHECK DAMAGED PARTS starter keys, Before further use of the too!, a guard or other part that 9. DON'T FORCE TOOL is damaged should be carefully checked to ensure that it it will do the job better and safer at the rate for which will operate properly and perform its intended function. it was designed. Check for alignment of moving parts, binding of moving 10. USE RIGHT TOOL parts, breakage of parts, mounting, and any other Don't force tool or attachment to do a job it was not conditions that may ,affect its operation. A guard or designed for. other part that is damaged should be properly repaired 11. WEAR PROPER APPAREL or replaced. Do not wear loose clothing, gloves, neckties or jewelry (rings, wrist watches} to get caught m moving parts. 21. DIRECTION OF FEED Nonslip footwear is recommended. Wear protective Feed work into a blade or cutter against the direction hair covering to contain tong hair. Roll long sleeves of rotation of the blade or cutter only. above the elbow. 12. USE SAFETY GOGGLES 22. NEVER LEAVE TOOL RUNNING WearSafety goggles (must comply with ANS! Z87.1 ) UNATTENDED at all times,; Ats0, use face or dust mask if cutting operation is dusty, and ear protectors (plugs or mUffs) Turn power off. Don't leave tool until it comes to a during extended periods of operation: complete stop. 2 Safety is a combination Of operator common sense and alertness at all times when the Jointer-Planer is being used. WARNING: FOR YOUR OWN SAFETY, DO NOT ATTEMPT TO OPERATE YOUR JOINTER-PLANER UNTIL IT IS COMPLETELY ASSEMBLED AND INSTALLED ACCORDING TO THE INSTRUCTIONS, .. AND UNTIL YOU HAVE READ AND UNDERSTOOD THE FOLLOWING, PAG E 1. GENERAL SAFETY iNSTRUCTIONS FOR POWER TOO LS .................................. 2 2. GETTING TO KNOW YOUR JOINTER-PLANER 12 3. BASIC MACHINE OPERATION ............... 18 4. USE OF HOLD-DOWN/PUSH BLOCKS ......... 19 5. MAINTENANCE ........................... 21 6. STABILI...
Dieses Handbuch ist für folgende Modelle:Jack Planes - 113.20680 (3.05 mb)