Stimmen - 2, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
Consequently, it is not recommended that this tool be used for extended work on any fiberglass material, wallboard, spackling compounds, or plaster. During any use on these materials, it is extremely important that the tool is cleaned frequently by blowing with an air jet. WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, also wear a dust mask. 13 MAINTENANCE MAINTENANCE LUBRICATION All of the bearings in this tool are lubricated with a suffi- cient amount of high-grade lubricant for the life of the unit under normal operating conditions. Therefore, no further lubrication is required. CLEANING CHIP EXHAUST AND EMPTYING CHIP BAG See Figure 16. After using your planer for an extended period of time or when planing wet or green lumber, chips may build-up in the chip exhaust port and require cleaning. Chip build- up restricts air flow and causes the motor to overheat. Unplug your planer. WARNING: Check extension cords before each use. If damaged replace immediately. Never use tool with a damaged cord since touching the damaged area could cause electrical shock resulting in serious injury. EXTENSION CORDS The use of any extension cord will cause some loss of power. To keep the loss to a minimum and to prevent tool overheating, use an extension cord that is heavy enough to carry the current the tool will draw. A wire gage size (A.W.G.) of at least 16 is recommended for an extension cord 100 feet or less in length. When working outdoors, use an extension cord that is suitable for outdoor use. The cord's jacket will be marked WA. Fig. 16 WARNING: Failure to unplug your planer could result in accidental starting causing serious injury. BLADE REPLACEMENT See Figures 17, 18, 19, 20, 21, and 22. The blades in your planer are reversible. Therefore, they can be reversed when one edge becomes dull. Always replace or reverse blades in pairs. Do not attempt to sharpen blades. If the blades become dull, replace them. When replacing the blades, use recommended replace- ment blade only, Ryobi part number HPL50K-26. Blades are sharp, use extreme caution when replacing blades. Unplug your planer. WARNING: Failure to unplug your planer could result in accidental starting causing serious injury. Secure your planer in an upside down position. Using the blade wrench provided, loosen the three blade securing screws on the blade holder. See Figure 17. NOTE: Do not over loosen the screws. If screws are too loose, alignment of the new blade will not be ac- ¦ Remove the chip bag from the chip exhaust. curate. ¦ Clean the chip or dust build-up from the chip exhaust port of your planer with a small piece of wood. Do not use your hands or fingers. ¦ Empty all chips from the chip bag and ensure collar is free from debris. ¦ Replace chip bag. Fig. 17 BLADE WRENCH BLADE SECURING SCREWS CUTTER HEAD LOOSEN BLADE SECURING SCREWS 14 MAINTENANCE MAINTENANCE NOTE: Before removing old blades, take notice of the ¦ Slide new blade into the slot of the blade holder. See direction of cut as well as how the tapered edge of the old Figure 20. blades are oriented. The tapered edge of the new blades must be in the same orientation as the original blades. Using the tip of a screwdriver, push blade out of blade holder. See Figure 18. Remove old blade from the blade holder. See Figure 19. NOTE: If blade cannot be pushed out of blade holder easily after loosening blade securing screws, use a block of wood to break the blade loose from the blade holder, with a short sharp blow. Then push with a screwdriver to remove the blades. If necessary, tap block of wood sharply with a small hammer to break blades loose. Clean any sawdust or wood chips from around the blade area. Fig. 19 BLADE WRENCH BLADE SECURING SCREWS Fig. 20 BLADE BLADE HOLDER BLADE BLADE HOLDER PUSH BLADE WITH TIP OF SCREWDRIVER PULL BLADE FROM BLADE HOLDER PUSH BLADE INTO BLADE HOLDER Fig. 18 Fig. 22 Fig. 21 RETIGHTEN BLADE SECURING SCREWS Use a screwdriver to push the blade into the blade holder until it is centered into position. See Figure 21. Using the blade wrench, retighten the three blade se- curing screws. See Figure 22. Repeat the above procedure to change the other blade. 15 MAINTENANCE MAINTENANCE BELT REPLACEMENT See Figures 23 and 24. When replacing the belt, use recommended replacement belt only, Ryobi part number HPL50K-03. ¦ Unplug your planer. ¦ Force the old belt from the small pulley by turning in the direction shown. As you turn the belt, pull and work it off the small pulley until it has been completely removed from both pulleys. ¦ Install the new belt over the large pulley. As you turn the belt, push and work it onto the small pulley until it is in place. Replace the belt cover. Install belt cover screw and tighten securely. SMALL PULLEY LARGE PULLEY Fig. 23 BELT COVER SCREW BELT COVER Fig. 24 WARNING: Failure to unplug your planer could result in accidental starting causing serious inj...