Stimmen - 5, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
Phillips screwdriver (not included) required to insert batteries. * Table of Contents Introduction . . . . . . . . . . . . . . . . . . .Page 2 Assembly and Batteries . . . . . . . . . . .Page 3-4 Begin Operation . . . . . . . . . . . . . . . .Page 5 Getting Started . . . . . . . . . . . . . . . . .Page 6 Detailed Description . . . . . . . . . . . . .Page 7-8 Companion Mode ..............Page 7-8 Game Play with R2 . . . . . . . . . . . . . .Page 9 Navigating R2 . . . . . . . . . . . . . . . . . .Page 10-11 R2 On His Own . . . . . . . . . . . . . . . . .Page 12 Troubleshooting . . . . . . . . . . . . . . . .Page 12 Using R2-D2’s Utility Arm . . . . . . . . . .Page 13 Tech Specs ...................Page 14 -2- Congratulations! You are a proud owner of R2-D2, an R2-series astromech utility droid from Industrial Automaton, the galaxy’s finest maker of service automatons, and distributed here on Earth by Hasbro. This droid is ready to obey certain commands, play games, and assist you on your Jedi missions. This particular R2 unit comes from the peaceful world of Naboo, where he and a team of astromechs served Queen Amidala aboard her Royal Starship. R2-D2 has seen and taken part in many amazing adventures. He fought valiantly alongside both Anakin and Luke Skywalker, aided the Old Republic during the clone wars, and was instrumental to the Rebellion against the Empire during the Galactic Civil War. R2-D2 (or, alternately, Artoo Detoo) has been newly programmed at our state-of-the-art factory to be your devoted helper and friend: to obey your commands, to act as your room sentry and guard, and to play fun games with you and your friends! R2’s vocabulary of electronic beeps and whistles doesn’t stop this droid from trying to communicate with human masters; he understands certain commands, and usually manages to get his points across, too! To get started, simply follow the instructions of this manual. Please be aware that R2 is an especially feisty astromech; when not treated well, he will let you know about it! But if you treat R2-D2 with the same loyalty and dedication that he will give to you, this little droid may help you to follow in the footsteps of the illustrious Jedi masters! -3- ASSEMBLY AND BATTERIES R2-D2 will be ready for action after the following power up procedures: DROID ASSEMBLY: 1.) Snap the head/projector piece onto the main unit. 2.) Snap the side legs onto each side of the main unit. 3.) As an option, you may also remove the sensor array from the top of R2’s dome and use the included telescope piece to extend it from his head. HEAD/PROJECT PIECE STEERING LEG STEERING LEG SENSOR ARRAY TELESCOPE -4- CAUTION: TO AVOID BATTERY LEAKAGE 1) Be sure to insert the batteries correctly and always follow the toy and battery manufacturers' instructions; 2) Do not mix old and new batteries or alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries; 3) Always remove weak or dead batteries from the product. ! INSTALLING BATTERIES: 1.) Use a Phillips screwdriver to loosen the two captive screws that secure the battery door in back, and remove the door. 2.) Open the compartment door. Insert four "AA" batteries into the compartment. Close the compartment door, then insert four "D" batteries on top as shown. (Re-chargeable batteries, such as NiCd or NiMH, will work well for the "D" cells, but are not necessary for the "AA" batteries.) 3.) Replace the battery door, and securely fasten the screws. BATTERY DOOR AA BATTERIES D BATTERIES COMPARTMENT DOOR -5- POWERING UP: 1.) Flip the switch located in the bottom back of the unit to power up your R2 unit. 2.) R2-D2 will automatically calibrate his head position sensor by rotating his head. 3.) R2-D2’s lights will blink alternately between red and blue as he warms up (about thirty seconds), and then they will blink red and blue together. This indicates that the warm-up period is complete, and R2 is ready to receive commands. 4.) Once R2 is powered up, your droid is always on (unless you choose to turn him off manually)! "WHEEL-LOCK" SETTING: When you first power up the R2 unit, the droid will remain in stationary "Wheel-Lock" mode until you press the button to release the wheels (press the same button when you want to lock the wheels again). Once the wheels are unlocked, he will move freely in response to your commands. When you want R2 to stand in place (for instance, for tabletop use), simply press the "Wheel-Lock" button located in the front center of the unit, as shown in illustration. When in this setting, the button will light up red to indicate that the wheels are locked. Press the same button again to release the wheel-lock setting. Master Power Control OFF ON Important Note: The treads on R2-D2’s steering legs can navigate floors and most carpeting. However, we strongly recommend you use R2-D2 indoors only. Never use R2-D2 near stairs, unless the stairs are protected. R2-D2 is unable to detect or navigate stairs and may fall down stairs and b...