Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED AND IMPLIED WARRANTIES. ATON EXPRESSLY DISCLAIMS ALL SUCH OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. Notwithstanding the above, where applicable, if you qualify as a “consumer” under the Magnuson-Moss Warranty Act, then you may be entitled to any implied warranties allowed by law for the Warranty Period. Some states do not allow limitations on how long an implied Limited Warranty lasts, so the above limitation may not apply to you. ATTENTION: TO OUR VALUED CONSUMERS Valid proof of purchase is required for all warranty services. Warranty service requests made without proof of date of purchase will be denied. Please keep the original sales receipt for your records and send a copy to request warranty service. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. * ATON is a division of ELAN Home Systems, LLC. or service@atonhome.com ©2007 • All rights reserved. P/N 227943 REV:B Figure 2 Introduction The ATON AIR5 is a miniature ‘plasma-friendly’ IR receiver designed to sit on a shelf, cabinet or any flat surface. This receiver uses advanced IR filtering technology which allows it to work even in areas that receive normally harmful interference (near plasma TV’s, compact flourescent lights, etc.). Features (Refer to Figure 1) • 3.5mm Quad Plug Accommodates STATUS, IR, +12VDC, & GND • ‘Plasma-Friendly’ Technology Helps Block Plasma TV Interference • IR Lens Rejects Visible Light Interference • Internal Crosshatch Shield Inhibits EMI/ESI Interference • STATUS Indicator: Green LED for System On/Off Indication • ACTIVITY Indicator: Blue LED Indicates IR Signal Activity Figure 1 Specifications: • Requires 12VDC power supply, termination block and IR emitters for IR operation. • Mounting: Sits on any flat surface. A special pad protects the surface on which the AIR5 is placed in addition to providing anti-skid action. • Power: 12VDC @ 6 mA • Carrier Frequency Acceptance Range: 28kHz to 90kHz. • Control Range: Up to 35 feet, depending on remote strength and ambient noise conditions • Control Angle: +/- 50 degrees off-axis • Room-to-Room Wire Recommendations: Cat-5 • Maximum recommended cable length: 1200 feet using Cat-5 • Dimensions: 3 3/16" (81mm) W x 1 1/8" (28mm) H x 1 1/16" (27mm) D IR Pickup Diode Status LED (Green) Activity LED (Blue) IR Lens 4-Conductor 3.5mm Plug +12VDC IR OUT GND STATUS 8' Lead 1-1/8" 3-3/16" 1-1/16" STATUS +12V GND IR OUT Red Black Yellow Internal Wire Colors White Stand-Alone System Connections: A: Basic System Figure 2 shows a basic IR distribution system using the ATON AIB4 Amplified IR Connection Block, AIR5 IR Receiver, and AIE2 Talk-Back IR Emitters to control source equipment. 1. Place the AIR5 on a shelf top, a cabinet or other horizontal surface. 2. Plug the AIR5 and IR emitters into the ATON AIB4, as shown. 3. Set the DIP switches on the AIB4 to LP ON and NET ON or OFF. 4. Plug in the power supply. 5. IR signals sent to the AIR5 will pass through the AIB4 and control the equipment. B: Multi-Room System Figure 3 shows an example of multiple ATON IR Receivers in a multi-room system. 1. Pull Cat-5 from each room (home runs) to the AIB4 terminator near the controlled components. NOTE: MAX DISTANCE of ALL Wire Runs is 1200 ft using Cat-5 cable. When using long lengths, the dipswitch on the AIB4 must be set to the NET ON position and a 500 Ohm resistor must be used. 2. Connect IR receivers in each room to the Cat-5 runs as shown, using the terminal strips supplied. 3. Connect the Cat-5 wires to the correct location on the AIB4 connection terminals (+12VDC, IR, STATUS, and GND). 4. Plug the AIE1 and AIE2 Emitters into the AIB4. 5. Set the DIP switches to LP ON and NET ON. 6. Plug the local AIR5 IR Receiver into the IR RECEIVER jack. 7. Plug in the PS2 12VDC Power Supply. 8. IR signals sent to the IR receivers will pass through the AIB4 and control the equipment. NOTE: Refer to the ATON AIB4 Instructions for power supply considerations and other important information. STATUS Brightness Figure 3 also shows how an external resistor can be added to reduce the brightness of the Status LEDs on ATON IR receivers. In this example, a PS2 12VDC Power Supply is used as the voltage source to indicate ON/OFF status of an A/V Receiver. Choose a resistor value that achieves the brightness you desire (about 2.2k to 12k, 1/8W). Connect it in series with the STATUS lead on each IR receiver, as shown. AIR5 Shelf Top IR Receiver Remote Control To 120V AC (unswitched) PS2 Power Supply AIB4 Amplified IR Connection Block A/V Receiver Satellite DVD AIE2 Talk-Back Emitter AIE2 Talk-Back Emitter AIE2 Talk-Back Emitter Figure 2 To 120V AC (unswitched) Power Supply A/V Receiver Satellite DVD AIR6 In-Wall IR Receiver AIR1 Surface-Mount IR Receiver AIR1 AIR5 Tabletop IR Rec...