Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
Advanced Tuner Operations Advanced Tuner Operations About the menu entry system This tuner uses a menu entry system which allows you to operate various functions by following messages on the display. Use the following controls for menu operation. Use To MENU Enter the menu mode. TUNING/SELECT Display different items or settings. ENTER Select the currently displayed item or setting. RETURN Return to a previous stage in the menu mode. Customizing the display You can select the appearance of the display from one of the following four display modes. 1 Press MENU, then turn TUNING/ SELECT until “Disp-Mode” appears in the display. 2 Press ENTER. “Select” appears in the display. 3 Turn TUNING/SELECT to select a display mode. Full Display/Full Brightness tFull Display/Dimmed tMinimal Display/Full Brightness tMinimal Display/Dimmed 4 Press ENTER. The setting remains in effect until you change it again. If you press one of the buttons on this unit, the minimal display changes to the full display with the selected brightness. After about 4 seconds, the display returns to the display mode you selected. Receiving broadcasts This tuner lets you enter a station’s frequency directly by using the numeric buttons (Direct Tuning). If you do not know the frequency of the station you want, see “Receiving broadcasts by scanning stations (Automatic Tuning)” on page 10. Before you begin, make sure you have connected an FM/AM antenna to the tuner as indicated on pages 5 and 6. 1 Press BAND repeatedly to select FM or AM (MW and LW). 2 Press DIRECT. 3 Press the numeric buttons to enter the frequency. Example 1: FM 102.50 MHz 1 0 2 5 0 Example 2: AM 1350 kHz 1 3 5 0 To receive other stations Repeat steps 1 to 3. Tips • When you tune in AM (MW and LW) stations, adjust the direction of the AM loop antenna for optimum reception. • If the STEREO indicator remains off, press FM MODE when an FM stereo broadcast is received. • If you cannot tune in a station and the entered numbers are flashing, make sure you have entered the right frequency. If not, press DIRECT and reenter the frequency you want. If the entered numbers are still flashing, the frequency is not used in your area. • If you enter a frequency not covered by the tuning interval, the entered value is automatically rounded up or down to the closest covered value. Tuning intervals for direct tuning are: FM: U.S. models: 100 kHz intervals Other models: 50 kHz intervals AM: U.S. models: 10 kHz intervals Other models: 9 kHz intervals (MW), 1 kHz interval (LW) continued Basic Operations/ Receiving broadcasts (continued) Receiving broadcasts by scanning stations (Automatic Tuning) With automatic tuning, you can quickly tune in a station without having to know its frequency. 1 Press BAND repeatedly to select either FM or AM (MW and LW). 2 Press TUNE MODE so that “AUTO TUNING” (“AUTO” for ST-SE370) appears in the display. 3 Turn TUNING/SELECT slightly and release it when the frequency numbers start changing. Turn the control to the right for a higher frequency; turn it to the left for a lower frequency. When the tuner locates a station, it stops automatically. “TUNED” appears in the display. The signal meter indicates the strength of the broadcast signal. 4 Repeat step 3 until you tune in the appropriate station. To store the station, see “Presetting radio stations” on page 8. If you cannot tune in the station you want (Manual Tuning) With manual tuning, you can search through all stations broadcasting on each band, and tune in stations with extremely weak signals that you might not be able to receive with automatic tuning. 1 Press BAND repeatedly to select FM or AM (MW and LW). 2 Press TUNE MODE so that only “TUNING” appears in the display (ST-SE570 only). “AUTO” should not appear in the display. For ST-SE370, press TUNE MODE until nothing appears in the display. 3 Turn TUNING/SELECT until you tune in the station you want. Turn the control to the right for a higher frequency; turn it to the left for a lower frequency. The signal meter indicates the strength of the broadcast signal. Note When you reach the highest or lowest frequency of any band, tuning stops. Tips for better FM reception This tuner has various functions designed for better reception. First, try to receive stations with the standard settings. If the reception is not good, try altering the reception quality to obtain a clear signal. The tuner stores the following adjustments, together with the frequency when you make a station preset. Setting the FM mode Press FM MODE a few times to select the reception mode, select either Auto stereo (no indication) or “MONO”. • Auto stereo mode receives stereo broadcasts with strong signals. Press FM MODE a few times so that “MONO” disappears. • “MONO” receives stations with weak signals. Stations will be received in monaural but with even less noise. Checking the signal strength You can use the digital signal meter to check the signal strength of FM frequencies. The display range is fro...
Dieses Handbuch ist für folgende Modelle:Receiver und Verstärker - ST-SE370 (177.48 kb)