Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
Refer servicing to qualified personnel only. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. Precautions On safety • Do not disassemble the cabinet as this may result in an electrical shock. Refer servicing to qualified personnel only. • Should any solid object or liquid fall into the cabinet, unplug the amplifier and have it checked by qualified personnel before operating it any further. On power sources • Before operating the amplifier, check that the operating voltage of the amplifier is identical with your local power supply. The operating voltage is indicated on the nameplate at the rear of the amplifier. • If you are not going to use the amplifier for a long time, be sure to disconnect the amplifier from the wall outlet. To disconnect the AC power cord (mains lead), grasp the plug itself; never pull the cord. • AC power cord must be changed only at the qualified service shop. On placement • Place the amplifier in a location with adequate ventilation to prevent heat built-up and prolong the life of the amplifier. • Do not place the amplifier near heat sources, or in a place subject to direct sunlight, excessive dust or mechanical shock. • Do not place anything on top of the cabinet that might block the ventilation holes and cause malfunctions. On operation Before connecting other components, be sure to turn off and unplug the amplifier. On cleaning the amplifier Clean the cabinet, panel and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzine. On the prevention of howling Do the following: —lower the volume. —keep the turntable as far from the speakers as possible. —use commercially available audio insulators on the bottom of the turntable. —keep the microphone away from the speakers during use. For further protection against howling, set the speakers or turntable on top of a heavy wooden board or concrete slab. If you have any questions or problems concerning your amplifier, please consult your nearest Sony dealer. Welcome! Thank you for purchasing the Sony Integrated Stereo Amplifier. Before operating the amplifier, please read this manual thoroughly and retain it for future reference. Conventions • Instructions in this manual describe the controls on the amplifier. For details on the remote buttons control, see “Remote Button Descriptions” on page 11. TABLE OF CONTENTS Getting Started Hookup Overview 4 Audio Component Hookups 4 Speaker System Hookups 5 Mains Lead Hookups 6 Listening to the Music 7 Recording 9 • The following icon is used in this Additional Information manual: Troubleshooting 10 z Indicates hints and tips for making Specifications 10 the task easier. Rear Panel Descriptions 11 Remote Button Descriptions 11 Unpacking Check that you have received the following supplied items: • Remote commander (remote) (1) RM-S316 • Sony batteries R6 (size-AA) (2) Inserting batteries into the remote Insert two R6 (size-AA) batteries, matching the + and – on the batteries with the markings inside the battery compartment. When using the remote, point it at the remote control sensor gon the amplifier. z When to replace batteries With normal use, the batteries should last for about 6 months. When the remote no longer operates the amplifier, replace all the batteries. Notes • Do not leave the remote near an extremely hot or humid place. • Do not drop any foreign object into the remote casing, particularly when replacing the batteries. • Do not expose the remote sensor to direct sunlight or lighting equipment. Doing so may cause a malfunction. • If you don’t use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion. Getting Started Getting Started Hookup Overview The amplifier allows you to connect and control the following audio components. Follow the hookup procedure indicated for each component that you want to connect. To learn the location and name of each jack, see “Rear Panel Descriptions” on page 11. Audio Component Hookups Overview Here you learn how to connect your audio components to the amplifier. PHONO y AUX TAPE1/DAT EON CONTROL INTUNER TAPE2/MDCD SPEAKERS EON CONTROL R B A L+ +– – R L+ +– – TAPE1/DAT L REC OUT IN IMPEDANCE USE 4–16W A+B USE 8–16W BI WIRE USE 4–16W IN R L R TAPE2/MD REC OUT IN AUX IN CD IN TUNER IN L R PHONO IN SIGNAL GND y Speaker (L) Speaker (R)TV or video deck Tape deckDAT deck Tuner CD playerTurntableMD deck PROTECTION UPHONES SPEAKERS A 0 BASS •OFF A+B –10 +10 TONE SUBSONIC INPUT SELECTOR VOLUME SOURCE DIRECT 0 10 .ON .OFF LOUDNESS . ON . OFF B gSOURCETAPE10 TREBLE • –10 +10 • BALANCE TAPE MONITOR CD TUNERAUX TAPE2/MD TAPE1/DAT PHONO • LEFT RIGHT EON LINK Before you get started • Turn off the power to all components before making any connections. • Do not connect the mains leads of the various components until all connections are completed. • Use t...