Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Give it a try! x Center speaker distance ( C DIST. X.X m) continued Set the distance from your listening position to the center speaker. Center speaker distance should be set from a distance equal to the front speaker distance (A on page 12) to a distance 1.5 meters closer to your listening position (B on page 12). Hooking Up and Setting Up the Speaker System x Surround speaker distance ( SL DIST. X.X m) SR Set the distance from your listening position to the surround speakers. Surround speaker distance should be set from a distance equal to the front speaker distance (A on page 12) to a distance 4.5 meters closer to your listening position (C on page 12). 15GB Multi channel surround setup (continued) x Surround speaker placement ( SRSL PL. XXXX)* This parameter lets you specify the height of your surround speakers for proper implementation of the Digital Cinema Sound surround modes. Refer to the illustration below. • Select “PL. LOW” if the location of your surround speakers corresponds to section A. • Select “PL. HIGH” if the location of your surround speakers corresponds to section B. 60 30 ABAB * These parameters are not available when “Surround speaker size ( SL SR )” is set to “NO”. Tip The surround speaker placement parameter is designed specifically for implementation of the Digital Cinema Sound modes with virtual elements. With the Digital Cinema Sound modes, speaker placement is not as critical as other modes. All modes with virtual elements were designed under the premise that the surround speaker would be located behind the listening position, but presentation remains fairly consistent even with the surround speakers positioned at a rather wide angle. However, if the speakers are pointing towards the listener from the immediate left and right of the listening position, the sound fields with virtual elements will not be as effective. Nevertheless, each listening environment has many variables, like wall reflections. Therefore, we recommend that you playback multi channel surround encoded software and listen to the effect each setting has on your listening environment. Choose the setting that provides a good sense of spaciousness and that best succeeds in forming a cohesive space between the surround sound from the surround speakers and the sound of the front speakers. If you are not sure which sounds best, select “PL. LOW” and then use the speaker distance parameter and speaker level adjustments to obtain proper balance. Adjusting the speaker level Use the remote while seated in your listening position to adjust the level of each speaker. Note The receiver incorporates a new test tone with a frequency centered at 800 Hz for easier speaker level adjustment. 1 Press ?/1 to turn on the receiver. 2 Press TEST TONE. “T. TONE” appears in the display and you will hear the test tone from each speaker in sequence. Front (left) t Center t Front (right) t Surround (right) t Surround (left) t Sub woofer 3 Adjust the speaker level and balance using the LEVEL menu so that the level of the test tone sounds the same from each speaker. For details on the LEVEL menu, see page 22. While adjusting, the test tone is output from the speaker whose adjustment is performed. 16GB 4 Press TEST TONE again to turn off the test tone. Tip You can adjust the level of all speakers at the same time. Press MASTER VOL +/– or turn MASTER VOLUME on the receiver. Note The adjusted value are shown in the display during adjustment. Checking the connections After connecting all of your components to the receiver, do the following to verify that the connections were made correctly. 1 Press ?/1 to turn on the receiver. 2 Turn on the component that you connected (e.g., DVD player or VCR). 3 Press the input selector button (e.g., DVD or VIDEO) to select the component (program source). 4 Start playing. If you do not obtain normal sound output after performing this procedure, see “Troubleshooting” on page 35 and take the appropriate measures to correct the problem. Tip You can also use INPUT SELECTOR on the receiver to select the component. Basic Operations Selecting the component INPUT SELECTOR Press INPUT SELECTOR repeatedly to select the component you want to use. To select Display/light up VCR VIDEO DVD player DVD Satellite tuner TV/SAT Built in tuner TUNER After turning on the component you selected, select the component and play the program source. • After selecting VCR or DVD player, turn on the TV and set the TV’s video input to match the component you selected. MUTING Press MUTING to mute the sound. “MUTING” appears on the display when the sound is muted. To cancel muting, press it again or turn up the volume. The muting function is also canceled when you turn the power off or disconnect the power cord. Basic Operations 17GB Enjoying Surround Sound You can take advantage of surround sound simply by selecting one of the receiver’s pre- programmed sound fields. They bring the exciting and powerful sound of movie theaters and concert hal...