Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Kenwood Dateigröße: 1.26 mb Dateiname: Unterrichtssprache:

3 Press the SETUP key. • The test tone is turned off. The receiver enters the mode for inputting the distance to the speakers. 4 For MANUAL selection, press the SETUP key each time to select the speaker channel. 5Input the distance to the speakers. 1 Select the DISTANCE from the set up displays and press the SETUP key again. 2 Measure the distance from the listening position to each of the speakers. Jot down the distance to each of the speakers. Distance to front speakers : ____ feet (meters) Distance to center speaker : ____ feet (meters) Distance to surround speakers : ____ feet (meters) 3 Use the MULTI CONTROL knob or keys to select the distance to the front speakers. The speaker indicator to be adjusted blinks. Indication in feet Indication in meters • The allowable setting range is 1 to 30 feet (0.3m to 9.0m) , adjustable in 1 foot (0.3m) increments. 4 Press the SETUP key to accept the settings. 5 Repeat steps 3 and 4 to input the distance for each of the speakers. 6 Setup is complete when the EXIT indication appears. • The speakers you have selected should appear on the display. Confirm that all the speakers have been correctly selected. 7 Press the SETUP key to exit the SETUP mode. Input level adjustment (analog sources only) If the input level of an analog source signal is too high, the CLIP indicator will blink to indicate the source signal. Adjust the input level. 1 Use the INPUT SELECTOR knob to select the source of which the input level you want to adjust. • You can store a separate input level for each input source. 2 Press the SOUND key repeatedly until the “INPUT” indication appears. 3 Use the MULTI CONTROL knob or keys to adjust the input level. • The input level may be adjusted to any one of three settings: 0dB, -3dB, and -6dB. (The initial setting is 0dB.) 4 Press the SOUND key again to return to the input indication. 17EN Normal playback Preparing for playback Listening to a source component Some preparatory steps are needed before starting playback. SPEAKERS ON/OFF ON/STANDBY(KRF-V5070D/ V4070D/ V5570D)(VR-705/715) POWER ON/STANDBY INPUT SELECTOR VOLUME CONTROL POWER AUTO INPUT SELECTOR ON/OFF(KRF-V5070D/ V4070D/ V5570D) Turning on the receiver 1 Turn on the power to the related components. 2 Turn on the power to this receiver by pressing POWER ON/ STANDBY (for VR-705/715) or POWER ON/OFF and ON/ STANDBY (for KRF-V5070D/V4070D/V5570D) key. Selecting the input mode If you have selected a component connected to the CD/DVD, VIDEO2, DVD or DVD/6CH (VR-715/KRF-V5070D only) jacks, make sure that the input mode setting is correct for the type of audio signal to be used. 8 Selecting MD/TAPE Select the source name corresponding to the component connected to the MD/TAPE jacks. The initial factory setting is “TAPE”. To change the source to “MD”, follow the steps below: 1 Use the INPUT SELECTOR knob to select “TAPE”. 2 Hold down the AUTO key for more than 2 seconds. • The source indication changes to “MD”. • To return to the original indication, repeat procedure 2. Setting the speaker status The speaker indicator lights up. Press the SPEAKERS ON/OFF key to switch the speaker on or off. Input Selector VOLUME 1Use the INPUT SELECTOR knob or keys to select the source you want to listen to. The input sources change as shown below: 1 “AUX” 2 “TUNER” 3 “CD/DVD” 4 “TAPE” or “MD” 5 “VIDEO1” 6 “VIDEO2” 7 “DVD” or “DVD/6CH” (for VR-715/KRF-V5070D only) 2Start playback from the selected source. 3Use the VOLUME CONTROL knob or VOLUME keys to adjust the volume. 18EN Normal playback Normal playback ACTIVE EQ VOLUME CONTROL PHONES MULTI CONTROL SPEAKERS ON/OFF MUTE LOUDNESS MULTI CONTROL BASS BOOST ACTIVE EQ TONE MUTE VOLUME Adjusting the TONE (remote control only) You can adjust the sound quality when the receiver is in the PCM stereo and analog stereo mode. 1 Press the TONE key to select the TONE mode. 2 Use the MULTI CONTROL knob or keys to select TONE ON/OFF. 3 When in TONE ON selection, press the TONE key for the following displays. BASS : Select this to adjust the low frequency range. TREB : Select this to adjust the high frequency range. 4 Use the MULTI CONTROL knob or keys to adjust the sound quality. • The bass and treble levels are adjustable from -10 to +10 in 2 step increments. Once-touch low frequency emphasis (BASS BOOST) (remote control only) You can adjust the sound quality when the receiver is in the PCM stereo and analog stereo modes. Press the BASS BOOST key. • Press the key once to select the maximum (+10) low frequency emphasis setting. • TONE will automatically be turned ON. • This key does not function when the receiver is in the sound quality or ambience effects adjustment mode. .~¶ Switching back the previous setting Press the BASS BOOST key again. Adjusting the LOUDNESS mode (remote control only) You can adjust the Loudness function which controls the low volume settings to maintain the music’s richness. The adjustment can be made when the receiver is in the PCM stereo and analog stereo m...

Herunterladen

Geben Sie zwei Ziffern: