Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: Kenwood
Dateigröße: 336.43 kb
Dateiname:
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Anleitung Zusammenfassung
indicator KBS (Kenwood Built-in Sound) "ROCK" "POPS" "VOCAL" "LOUD1" "LOUD2" "LOUD3" "PRESET1" "PRESET2" "PRESET3" Equalizer curve /Spectrum analyzer display USER indicator Buttons and Display Release button MENU indicator DEMO indicator Title display No. indicator KBS / USER indicator — 5 — You can adjust the sound level to suit your preference among 11 frequencies: 60 Hz, 120 Hz, 250 Hz, 380 Hz, 500 Hz, 750 Hz, 1 kHz, 2 kHz, 4 kHz, 8 kHz, and 16 kHz. Selecting Band for Adjustment: Each time you press the 2 button, the band shifts to the left (lower frequencies), while each time you press the 3 button, the band shifts to the right (higher frequencies). Increasing Level: Press the ubutton while the band indicator is blinking. The level indicator goes up. The level can be adjusted up to +12 (by two steps). Decreasing Level: Press the dbutton while the band indicator is blinking. The level indicator goes down. The level can be adjusted down to -12 (by two steps). • When adjusting the equalizer level, do not adjust solely a single band. Adjust each band to form a curve. • Equalizer adjustment mode will be cancelled automatically if no buttons are pressed for five seconds. NOTE Equalizer Adjustment You can store four types of adjusted equalizer curves in memory, and can call up an original equalizer curve at the touch of a button. To adjust the sound quality to your preference. Hold down any one of buttons 1 to 3 for more than 2 seconds. The adjusted equalizer curve will be stored in memory. Up to 3 equalizer curves can be stored in memory. Recalling Equalizer Curve from Memory: Press the EQ button, select "USER MODE". Press any one of buttons 1 to 3. The equalizer curve stored by the respective button number (1 to 3) will be recalled. The number (1 to 3) of the pressed button is displayed. 2 1 NOTE 2 1 Equalizer Curve Memory Other oper ations Menu System To accommodate system has been employed Press the MENU button to enter the function to make the English Adjustment mode (Display) Operation of Control u button d button Fader (“FADER”) Front channel emphasized.(F15) Rear channel emphasized.(R15) High-pass You can select the frequency to filter for front follows: output OFF (through) O 40Hz O 60Hz O 80Hz O (“HPF-F”) 100Hz O 120Hz O 150Hz O 180Hz O 220Hz High-pass You can select the frequency to be cut, as filter for rear follows: output OFF (through) O 40Hz O 60Hz O 80Hz O (“HPF-R”) 100Hz O 120Hz O 150Hz O 180Hz O 220Hz Low-pass filter for You can select the frequency to be cut, as subwoofer follows: output 50Hz O 80Hz O 120Hz O OFF (through) (“LPF-S”) Subwoofer Preout Level (“ SUBW-LV”) The subwoofer sound is increased. The subwoofer sound is decreased. Analizer level* 1 (“ ANA LV”) The spectrum analyzer level increased. The spectrum analyzer level decreased. LCD contrast level* 2 (“ LCD CNT”) The setting values higher. The setting values lower. Rear / Front output boost* 3 (“ PREOUT”) Boost on.(“HIGH”) O Boost off.(“LOW”) 1 2 3 4 Press the MENU button to enter the MENU indicator lights. Press the 2 or 3 button. Each time the button is pressed, the change as follows: ”MENU FADER" (Fader) °5 ”MENU HPF-F" (High-pass filter for front output) °5 ”MENU HPF-R" (High-pass filter for rear output) °5 ”MENU LPF-S" (Low-pass filter for subwoofer output) °5 ”MENU SUBW LV" (Subwoofer preout level) °5 ”MENU ANA LV" (Analizer level)* 1 °5 ”MENU LCD CNT" (LCD contrast level)* 2 °5 ”MENU PREOUT" (Rear / Front output boost)* 3 5 Press the u or d button. Look at the table to adjust the mode being displayed. Press the MENU button to end the function set mode. *1: It varies according to the volume setting on the centre unit, so set the volume level to normal on the centre unit before adjusting it. *2: The contrast on the equaliser/spectrum analyser display is not adjustable. *3: If the sensitivity of the connected amp is high enough to accommodate 4V, set the boost level to "HIGH". Otherwise, set it to "LOW".If it has been set to "HIGH", set the input sensitivity on the amp side to 4V. If it is set lower than 4V, noise may be output. Table of Adjustment NOTE The menu settings cannot be stored in the user memory. — 6— Spectrum Demonstration You can select the Switching the Spectrum Analyzer Display: Each time you press the button, the spectrum analyzer display switches as follows; t 1 "SCAN MODE ON":Displays 2 to 9 are automaticallyshown in succession for about five seconds t 2 "PEAK HOLD" t 3 "LASER" t 4 "H-SCOPE" t 5 "FIREWORKS" t 6 "SQUASH" t 7 "V-SCOPE" t 8 "BLIZZERD" t 9 "KISS" t 0 "SIDE WAVE" t ! "EQ CURVE":Equalizer curve t @ "SPEANA OFF":Spectrum analyer off Automatic Dimmer Function The display dims when the car's lights are turned on. NOTE The dimmer function is not available for units if the dimmer cable is not connected. You can give a demonstration the equlizer curves DEMO indicator lights on. Starting Demonstration: Pressing the S.A button for more demonstration mode. Cancelling Demonstration: Press the S.A button. In...