Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
MANU./REF. key Press to switch the manual and refer* ( ) A MEMORY key Press this key when registering a user- created equalizer pattern. Genre keys Press in the genre mode to select the desired music genres and their equalizer patterns. Frequency keys (F1, F2, F3) Each key can store a desired center frequency. FREQUENCY JOG knob Rotate the control knob to adjust the frequency band (range). 8 GRAPHIC/PARAMETRIC key GRAPHIC: Select this mode when adjusting an equalizer curve. PARAMETRIC: Select this mode when creating an equalizer curve according to center frequencies. & ence functions alternately. Preset keys (1 to 5) Typical equalizer patterns have been preset under these keys so that you can select any one of them easily. STANDBY indicator While standby mode is indicated, a small amount of power is supplied to the system to back up the memory. In this mode, the system can be turned ON by remote control. System connections G-EQ300 (En/K) Make connection as shown below. When connecting the related system components, refer also to the instruction 8 manuals of the related components. 3 Caution: Do not plug in the power lead until all connections are completed. Malfunction of microprocessor If operation is not possible or erroneous display appears even though all connections have been made properly, reset the microprocessor referring to “In case of difficulty”. . Caution regarding placement ( Except for U.S.A., Canada ) To maintain proper ventilation, be sure to leave a space around the unit (from the largest outer dimensions including projections) equal to, or greater than, shown below. Left and right panels: 10 cm, rear panel: 10 cm *CAUTION (For U.K.) When using the AC outlet epuipped with this unit, be sure to consult your AV CONTROL CENTER dealer for the correspond-ing plug. LINE IN OUT R L R L TAPE PLAY IN REC OUT SYSTEM CONTROL R L REC PLAY TAPE 2 (MONITOR) SYSTEM CONTROL L R REC IN LINE PLAY OUT Connect to the TAPE 2 (MONITOR) jacks Set the TAPE 2 (MONITOR ) switch to the monitoring position. Audio cords Audio cords System control cord To wall AC outlet This unit Cassette tape deck (optional) U.K. * Australia U.S.A., Canada, China and US military Other countries Use the numbers 9 0 ! @on the rear panel of this unit when connecting it to an AV CONTROL CENTER or RECEIVER. Connections are easily completed by using Audio cords to make connections to the same numbers on the other component. .When a cassette deck is connected to the graphic equalizer,do not connect the system control cord to the cassette deck. .When connecting the audio cords (cords with pin plugs on each end), insert the white plugs into the L(Left) jacks and red plugs into the R (Right) jacks. NotesNotes 1. Connect all cords firmly. If connections are loose there could be loss of sound or noise produced. 2. When plugging and unplugging connection cords, be sure to first remove the power cord from the AC outlet. Plugging/unplugging connection cords without removal of the power cord can cause malfunctions or damage on the unit. 3. Do not connect up a power source which is larger than that indicated on the socket at the rear of the unit. System connections G-EQ300 (En/K) About the system control connections SYSTEM CONTROL SYSTEM CONTROL SYSTEM CONTROL SYSTEM CONTROL SYSTEM CONTROL *4 When this unit is connected to KENWOOD audio component system “SERIES 21”, also connect them through the system control cords to allow system-control operations between components. Connection example The SERIES 21 components which can be system-connected with this unit include the LD player, MD recorder and DVD player. 1. Do not connect the SERIES 21 components to other system components using system control cords. 2. Do not connect system control cords to any components other than those specified by KENWOOD. It may cause a malfunction and damage your equipment. 3. Be sure the system control plugs are in- serted all the way in to the system control terminals. *4.When a cassette deck is connected to the graphic equalizer,do not connect the sys- tem control cord to the cassette deck. About the system control operations (Available operations when SERIES 21 components are connected through system control cords) NotesNotes POWER AMPLIFIER GRAPHIC EQUALIZER CASSETTE DECK 1 CASSETTE DECK 2 CD PLAYER AV CONTROL CENTER Remote Control Lets you operate source components with the system remote supplied with AV CONTROL CENTER. Automatic Operation When you start playback from a source component, the input selector on AV CONTROL CENTER switches to that component automatically. (Except TAPE 2) Synchronized Recording Lets you synchronize recording with the start of playback when recording from CD or LD . System control cord System control cord System control cord Display G-EQ300 (En/K) Preparation ¦Ensure that the MAIN POWER key is set to ON. MAIN POWER -ON .OFF : Keys and control used in the operations described on this page. Switching the display modes 1 1 Press the ON/STANDBY k...