Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
m O POWER switch Press this switch to turn the power on. Press it again to turn the power off. @ Display window © Preset station indicator Lights up to indicate the pressed preset station button. ® STATION FREQUENCY display Displays the band and frequency of the received station. (D IF MODE AUTO/NARROW/WIDE indicator AUTO: When the Auto IF Mode is selected with the IF MODE AUTO/MAN’L button, this indicator lights. NARROW/WIDE: In Manual IF Mode, when the tuning mode is selected with IF MODE NARROW/WIDE button, the corresponding indicator lights. © SIGNAL QUALITY indicators SIGNAL QUALITY meter: Indicates the level of the received frequency. If multipath interference is detected, the signal quality level indication decreases. CSL (Computer Servo Lock): This indicator lights when the Computer Servo Lock (CSL) system Is activated during FM reception mode. For details, refer to “Technical notes on the Computer Servo Lock (CSL) system” descrived later. FINE TUNING: When the FINE TUNING button is operated, this indicator lights. FM STEREO: When an FM stereo broadcast with a sufficient signal strength is received, this indicator lights. © P1-P8/P9-P16/P17-P24 indicators Indicates the range of the preset station buttons. 13 © MEMORY indicator When the MEMORY button is pressed, this indicator biinks for about 5 seconds. During this period, the displayed frequency can be memorized with one of the preset buttons. ® AUTO ST indicator When the MODE AUTO/MAN’L button is set to AUTO and the MODE FM/ MONO button is set to FM to receive an FM broadcast with a sufficient signal, this indicator lights. (8) BLEND indicator Indicates that the BLEND tuning mode is activated with the BLEND button. (D RF ATT indicator Indicates that the RF ATT tuning mode is activated with the RF ATT button. © ANT A/B indicator Indicates the antenna terminal at the rear panel that has been selected with the ANTENNA A/B button. © AUTO TUNING indicator Indicates that the AUTO TUNING mode is selected with the TUNING MODE AUTO/MAN’L button. © LOCK indicator Indicates that the LOCK function is activated to lock in the required frequency. ® TUNING control Tune to the required station by turning this control. This control is also used to select a character for the name of a received station. O Preset station buttons The preset station buttons are used to store up to 24 station frequencies, including reception modes. 0 P1-8/P9-16/P17-24 button Press this button to change the range of the preset station buttons. When this button is pressed, the selected range indicator, ( P1-P8, P9-P16, or P17-P24) flickers for about 5 seconds, and then lights. 0 MODE AUTO ST/MONO button To receive an FM stereo broadcast of sufficient signal strength in stereo mode, set the TUNING MODE AUTO/MAN’L button to AUTO and this button to AUTO ST, so that the AUTO ST indicator lights. To receive a weak FM broadcast, set the TUNING MODE AUTO/MAN’L button to MAN’L and this button to MONO, so that the AUTO ST indicator goes off. The received broadcast is heard in monaural mode. O MEMEORY button When this button is pressed, the MEMORY indicator blinks for about 5 seconds. During this period, press the desired preset station button to store the displayed frequency. This button is also used to memorize the station name. @ BLEND button If this button is set to ON, and the S/N ratio of a stereo signal is less than about 50 dB, the right and left channel are blended accordingly. When the MODE button is set to MONO, the BLEND function does not work even when this button is set to ON. © IF MODE buttons Used to vary the band pass width of the FM intermediate frequency, between WIDE and NARROW. AUTO/MAN’L: Used to select the Auto or Manual IF Tuning mode. When the Auto IF Tuning mode is selected, the AUTO indicator lights and the tuner automatically selects the IF band pass width (WIDE or NARROW). When you want to select the IF band pass width by yourself (Manual IF Tuning mode), press this button so that the AUTO indicator goes off, and then select the IF band pass width with the NARROW/WIDE button. NARROW/WIDE: Press this button to select the IF band pass width in Manual IF Tuning mode. Before you operate this button, be sure to press the AUTO/MAN’L button so that the AUTO indicator goes off. When the reception signal is strong, press this button so that the WIDE indicator lights to obtain distortion-free sound. When the reception signal is weak, or when the desired station is interfered with by adjacent stations, press this button so that the NARROW indicator lights to increase the selectivity. ® RF ATT button Used to decrease the RF cross modulation and intermodulation. In addition, it can be used together with the IF MODE button to improve the reception signal condition. When the reception signal is strong, press this button to ON, so that the RF ATT indicator lights. In this position, the RF cross modulation and intermodulation wi...