Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
• The following icons are used in this manual: Indicates that you can use only the remote to do the task. Indicates hints and tips for making the task easier. Receiver Operations Selecting a Component 8 Receiving Broadcasts 9 Presetting Radio Stations 10 Recording 11 Additional Information Troubleshooting 12 Specifications 13 Index 14 Rear Panel Descriptions 14 Remote Button Descriptions 15 Quick Reference Guide (Back cover) Getting Started Unpacking Check that you received the following items with the receiver: • FM wire antenna (1) • AM loop antenna (1) • Remote controller (remote) (1) • Size AA (R6) batteries (2) Inserting batteries into the remote Hookup Overview The receiver allows you to connect and control the following audio components. Follow the hookup procedures for the components that you want to connect to the receiver on the pages specified. To learn the locations and names of each jack, see “Rear Panel Descriptions” on page 14. Audio/Video Component Hookups (5) TV tuner Insert two size AA (R6) batteries in accordance with the + and – markings on the battery compartment. When using the remote, point it at the remote sensor g on the receiver. ] ] }} When to replace batteries Under normal use, the batteries should last for about 6 months. When the remote no longer operates the receiver, replace both batteries with new ones. Notes • Do not leave the remote in an extremely hot or humid place. • Do not use a new battery with an old one. • Do not expose the remote sensor to direct sunlight or lighting apparatuses. Doing so may cause a malfunction. • If you don’t use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion. Cable TV VCR Antenna Hookups (5) AM/FM antenna System Hookups (6) Speaker CD player Front speaker (L) Front speaker (R) Tape/MD deck Turntable Before you get started • Turn off the power to all components before making any connections. • Do not connect the AC power cords until all of the connections are completed. • Be sure to make connections firmly to avoid hum and noise. • When connecting an audio cable, be sure to match the color-coded pins to the appropriate jacks on the components: White (left, audio) to White; and Red (right, audio) to Red. Getting Started Getting Started Antenna Hookups Overview This section describes how to connect AM and FM antennas to the receiver. If you want to receive radio broadcasts with the receiver, complete these connections first, then go to the following pages. For specific locations of the terminals, see the illustration below. ANTENNA What antennas will I need? • FM wire antenna • AM loop antenna (supplied) (1) (supplied) (1) Hookups FM wire antenna Receiver AM loop antenna ANTENNA AMFM 300 After connecting the wire antenna, keep it as horizontal as possible. If you have poor FM reception Connect a 75-ohm coaxial cable (not supplied) to an FM outdoor antenna. Pull back the mesh portion surrounding the inner cable and connect it to the earth terminal (right side). Connect the inner cable to the FM terminal (left side). Receiver ANTENNA FM 75 If you have poor AM reception Connect a 20 to 50 ft. (6 to 15-meter) insulated wire (not supplied) to the AM antenna terminal in addition to the AM loop antenna. Try to extend the wire outdoors and keep it horizontal. Connecting a ground wire To prevent hum, connect a ground wire (not supplied) to the yground terminal. If you’ve connected an outdoor antenna, be sure to connect the ground for lightning protection. Receiver ANTENNA AM . to ground Where do I go next? If you want to connect other components, go on to the next section. If you’re only planning to use the receiver to listen to the radio, go to “Speaker System Hookups” on pages 6 and 7. Audio/Video Component Hookups Overview This section describes how to connect your audio, and video (audio signal only) components to the receiver. If you want to use the receiver as an amplifier, complete these connections. For specific locations of the jacks, see the illustration below. y CD TV VIDEO PHONO TAPE/MD What cords will I need? Audio cords (not supplied) (1 for each CD player, turntable, TV tuner or cable TV; 2 for each tape deck, MD recorder or VCR) White (L) White (L) Red (R) Red (R) (continued) Getting Started Getting Started Hookups The arrow .indicates signal flow. CD player Receiver CD player Turntable CD IN L R OUTPUT LINE L R Receiver Turntable PHONO IN L R OUTPUT LINE L R • If your turntable has an earth lead To prevent hum, connect the earth lead to the y ground terminal on the receiver. Tape deck or MD recorder Receiver Tape deck or MD recorder IN OUTPUT LINE INPUT LINE L R TAPE/MD REC OUT L R TV tuner or Cable TV Receiver TV tuner or Cable TV TV AUDIO IN L R OUTPUT VIDEO L R VCR Receiver VCR AUDIO IN VIDEO AUDIO OUTPUT AUDIO INPUT AUDIO OUT L R L R Where do I go next? Go on to the next section to connect the speakers. Speaker System Hookups Overview This section describes how...