Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
2 Press a function button to select the component you want to use: To listen to or watch Press Records PHONO Radio programs TUNER Compact discs (CD) CD Audio tapes or MiniDiscs TAPE/MD (MD) TV programs or Cable TV TV Video tapes VIDEO 3 Turn on the component, for example, a CD player, and then start playing. To tune in radio stations on this receiver, see “Receiving Broadcasts” on page 9. 4 Turn VOLUME or press VOL +/– on the remote to adjust the volume. To Do this Mute the sound Press MUTING on the remote. Press again to restore the sound Reinforce the bass Press BASS BOOST to turn on the BASS BOOST indicator. Adjust the balance Turn the BALANCE control left or right. Adjust the tone quality Adjust the BASS and TREBLE controls. When you listen with headphones Connect the headphones to the PHONES jack and set the SPEAKERS buttons to OFF. To turn off the components Press POWER. You can turn off the video and audio components connected to the SWITCHED AC OUTLET at the same time. Receiver Operations Receiver Operations Receiving Broadcasts This receiver lets you enter a station’s frequency directly by using the numeric buttons (direct tuning). If you don’t know the frequency of the station you want, see “Receiving broadcasts by scanning stations (automatic tuning)” on this page. Before you begin, make sure you have: • Connected an FM/AM antenna to the receiver as indicated on page 5. • Selected the appropriate speaker system. (See “Selecting the speaker system” on page 7.) POWER Numeric buttons VOLUME FM/AM DIRECT TUNER TUNING +/– 1 Press POWER to turn on the receiver. 2 Press TUNER. The last received station is tuned in. 3 Press FM/AM to select FM or AM stations. 4 Press DIRECT. 5 Press the numeric buttons to enter the frequency. Example 1: FM 102.50 MHz Example 2: AM 1350 kHz 1 0 2 5 0 (You don’t have to enter the last “0.”) 1 3 5 6 When you tune in AM stations, adjust the direction of the AM loop antenna for optimum reception. To receive other stations Repeat Steps 3 to 5. If the STEREO indicator remains off Press FM MODE when an FM stereo broadcast is received. If an FM stereo program is distorted The STEREO indicator flashes. Press FM MODE to change to monaural (MONO). You will not have the stereo effect but the distortion will be reduced. To return to stereo mode, press this button again. If you cannot tune in a station and the entered numbers are flashing Make sure you’ve entered the right frequency. If not, press DIRECT and re-enter the frequency you want. If the entered numbers still flash, the frequency is not used in your area. To watch FM simulcast TV programs Make sure that you tune in the simulcast program both on the TV (or the VCR) and on the receiver. If you enter a frequency not covered by the tuning interval The entered value is automatically rounded up or down to the closest covered value. Tuning intervals for direct tuning are: FM: 50 kHz intervals AM: 10 kHz intervals (to change to 9 kHz intervals, see page 13) Receiving broadcasts by scanning stations (automatic tuning) If you don’t know the frequency of the radio station you want, you can have the receiver scan all the receivable stations to locate the one you want. 1 Press TUNER. The last received station is tuned in. 2 Press FM/AM to select FM or AM. 3 Press TUNING + or –. Press the + button for a higher station number; press the – button for a lower one. When you tune past either end of the band, the receiver automatically jumps to the opposite end. Every time a station is received, the receiver stops scanning. To continue scanning, press the button again. Receiver Operations Receiver Operations Presetting Radio Stations You’ll most likely want to preset the receiver with the radio stations you listen to often so that you don’t have to tune in the station every time. The receiver can store a total of 30 FM or AM stations. You can store the stations on preset numbers combining 3 characters (A, B, C) and numbers (0 - 9). For example, you can store a station as preset number A1, B6 or C9, etc. Numeric buttons SHIFT TUNER MEMORY 1 Press TUNER. The last received station is tuned in. 2 Tune in the station you want. If you are not familiar with how to tune in a station, see “Receiving Broadcasts” on the previous page. 3 Press MEMORY. “MEMORY” appears for a few seconds. Do steps 4 and 5 before “MEMORY” goes out. 4 Press SHIFT to select a character (A, B or C). Each time you press SHIFT, the letter “A,” “B” or “C” appears in the display. If “MEMORY” disappears, start again from step 3. 5 While MEMORY is displayed, press the number you want to use (0 to 9). 6 Repeat Steps 2 to 5 to preset other stations. To change a preset station Preset a new station on the number you want to change. Note If the AC power cord is disconnected for about one week, the preset stations will be cleared from the receiver’s memory, and you will have to preset the stations again. Tuning preset stations (preset tuning) You can tune directly to a preset station by enter...