Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: B&K Dateigröße: 6.3 mb Dateiname: Unterrichtssprache:

Plug one RJ- 45 end into the main RJ-45 jack on the back panel of the receiver. Plug the other end into the RJ-45 jack labeled Master IN on the back of the keypad. The main RJ-45 jack on the receiver will supply connections for +12VDC power @ 200mA, IR data and +12V control @ 50mA. See page 36 for the main RJ-45 pin out description. A keypad can be configured to control connected sources with IR by setting the control outputs to REMOTE. See the control output configuration page 34. A CK1.2 keypad can be programmed to control either the main theater zone, Zone B or both. Theater Zone status can be displayed on the keypad by pressing the backlight button. ZONE A & ZONE B IR INPUTS Two IR inputs are located on the back panel of the receiver. They are labeled IR IN, Zone A & Zone B. The IR inputs use a 3.5mm mono mini jack. Internally, both the Zone A and Zone B IR signals are summed before they are sent to the processor. Your processor can be controlled by a directly connected IR repeater system in combination with or in place of the supplied remote control. Connect the IR input cable to the processor using a mono 3.5 mm plug. The plug must be wired as tip (+) and the sleeve (-). The inputs are standard 38kHz modulated IR type with a voltage range of +5 to +12 VDC. AM / FM ANTENNA CONNECTION The B&K receiver contains one internal AM/FM tuner. To connect the AM antenna, use the AM antenna connection block and the AM antenna supplied. The AM is a push type. Strip . inch of insulation off your AM antenna wires and insert one wire end into each hole while holding the tabs down. Release the tabs to lock in the AM antenna wires. The FM jack is a standard screw on F-type connector. To connect the FM antenna use the dipole antenna supplied. 21 AVR 517 Series 2 AVR 517 Series 2 SETTING UP THE SYSTE M The setup of the receiver will require navigation through the menu system. The system menu will display on the front panel as well as an On-Screen Menu format. The OSD menu is available on all three video format types. B&K recommends that a video monitor, connected to a Zone A video output, be used in conjunction with the SR10.1 remote to setup the system using the OSD menu. It is possible to set up your receiver directly from the front panel. The descriptions below are general instructions for using and navigating the menu system. A complete navigational menu system flow chart is located on page 58. B&K supports setup software (BKcSuite) that can be used to assist in the setup of the receiver. BKcSuite setup software is available on our website at BKcSuite provides a fast and easy way to configure the system parameters of the receiver using a personal computer or laptop equipped with a serial port. You can save the configuration files for later use or as a backup. Directions for installing the BKcSuite are available on page 54 or on our website. BKcSuite is compatible with any B&K audio processor and can be used in conjunction with the SR10.1 Remote or CK1.2 Keypad programming software. THE MENU SYSTEM MENU Button - Pressing the MENU button either on the remote or on the front panel will activate the menu system. Once you are in the menu system, the MENU button will step back to the next higher-level menu or, if you are already at the highest level, it will exit from the menu system. EXIT (remote only) - From the remote control you may instantly exit the menu system by pressing the EXIT button. From the front panel press Menu repeatedly until you leave the menu system UP/DOWN ARROWS -Once you are in the menu system, use the UP/DOWN ARROWS to move to the desired menu selection. With the supplied SR10.1 remote, rocking the thumb pad forward and backwards act as the up and down arrows.The current active menu line is highlighted in a contrasting color in the On-screen display and also shown on the front panel display. SELECT / ENTER -Some menu selections select another menu level to be activated. Use the UP/DOWN ARROWS to move to the desired menu line. Pressing SEL or ENTER will activate the next menu. With the supplied SR10.1 remote, pressing on the center of the thumb pad also acts as the ENTER key. NUMERIC KEY DIRECT ENTRY (remote only) -From the remote control you may also go directly to a menu line by typing the corresponding line number. If there is another menu level below that line it will be activated immediately (no ENTER required). LEFT / RIGHT ARROWS (remote) or Volume Knob (front panel) -To change menu parameters, press the LEFT or RIGHT arrows to change the setting. There are no LEFT or RIGHT arrows on the front panel. The volume knob acts as the LEFT or RIGHT arrows. With the supplied SR10.1 remote, rocking the thumb pad left and right act as the left and right arrows. TEXT EDITING -Some menu selections will allow you to edit text. Use the UP/DOWN ARROWS to change the current (blinking) character. Use the LEFT/RIGHT ARROWS (or VOLUME KNOB) to move to another character position. Additiona...

Herunterladen

Geben Sie zwei Ziffern: