Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
Move sound out into the front speakers to improve the overall front image, or add sound to the center speaker to fix the center image. You can choose a level between 0 (the center speaker is dominant) and 7 (center sound is spread out). The default level is 3. _ EFFECT © Press [ q ] to select “C-WDTH”. (2) Press [ q ] or [ q ] to adjust the effect Dimension Control - DIMEN You can make up for differences in the output level of the front and surround speakers. You can choose a level between -3 and +3 - Increase the level to move sound to the front speakers, decrease to move it to the surround speakers. The default is level 0. „ EFFECT © Press [ o ] to select “DIMEN". CD Press [ q ] or [ q ] to adjust the effect. You can adjust the effect of MUSIC with the center image control. Center Image Control - C-IMG This adjustment helps you realize a more natural sound image when listening to music. Move sound out into the front speakers to improve the overall front image, or add sound to the center speaker to fix the center image. You can choose a level between 0 (the center speaker is dominant) and 5 (center sound is spread out). The default level is 3. ^ EFFECT (D Press [ o ] to select “C-IMG”. © Press [ q ] or [ q ] to adjust the effect. You can adjust the sound field by adjusting the level of the speakers and the delay time of the surround speakers. These adjustments can be made for each SFC mode. To adjust the speaker level _ LEVEL CD Press [ ) ] to select the speaker channel. Each time you press the button: C — SR — SL — SW t_I Speakers_set as “NONE” or “NO” are skipped. © Press [ q ] or [ q ] to adjust the level. C, SR, and SL: -10 dB to +10 dB SW: — (off) — MIN ■—* 1 - 19 «-*■ MAX To adjust the delay time © Press i^]. @ Press I o 1 or [ q ] to change the delay time. Delay time can be set at 10-millisecond (ms) intervals between 10 and 100 ms. The factory setting is 50 ms for each mode. RQT6208 Control guide Memory button [MEMORY] For presetting radio stations. Help/reset button [-HELP, -RESET] Press if an error message appears. A message offering a possible solution scrolls across the display. To reinitiate the unit’s settings, press and hold until “RESET1 appears. Band select/FM mode select button [-BAND, -FM MODE] For switching between AM and FM. If reception is poor in FM, press and hold until “MONO" appears to switch to monaural mode. Standby/on button [POWER, 6/1] Press to switch the unit from on to standby mode or vice versa. In standby mode, the unit is still consuming a small amount of power. Speaker A/B select buttons [SPEAKERS, A, B] Turning the speakers off automatically engages the STEREO mode (when listening through headphones, for example). If your speakers have an impedance under 6 Q Press and hold [A] or [B] until “LOW IMP" lights up on the display. Note that when "LOW IMP” is on, SPEAKERS A and B cannot be used at the same time. Headphone jack [PHONES] Plug type: 6.3 mm (1/4*) stereo Avoid listening for prolonged periods of time to prevent hearing damage. Turn the speakers off when using the headphones. Tuning buttons [TUNING, V, A] For tuning the radio and selecting preset stations. Press and hold until the frequency starts scrolling to start automatic tuning. Tuning stops when a station is found. Tuning intervals: FM-0.2 MHz, AM-10 kHz Preset channel button [PRESET] Press to allow preset station selection with [TUNING, V, A], NEO:6 mode select button [NEO:6] Use when “NEO:6” lights in the ENHANCED SURROUND mode. Dolby Pro Logic II mode select button [DOLBY PRO LOGIC II] Use when “HI PRO LOGIC D “ lights in the SURROUND mode. Enhanced surround mode select button [ENHANCED SURROUND] DSP sound mode selector [DSP SOUND MODE] For selecting “STEREO", “SURROUND” or “SFC”. The display General display Shows the input mode, radio frequency, and other general information. Speaker indicators [LOW IMP, SPEAKERS H, E] LOW IMP: You have switched to LOW IMP because you have connected speakers with an impedance under 6 il SPEAKERS □: Sound is output from speakers connected to the front A, surround, and center terminals. SPEAKERS ID: Sound is output only from speakers connected to the front B terminals. SPEAKERS □ ID: Sound is output from speakers connected to the front A and B terminals. Radio indicators [TUNED, STEREO, MONO, M\ TUNED: A station is tuned. MONO: You have switched to monaural mode with [-BAND, -FM MODE] to improve reception. STEREO: A stereo FM broadcast is tuned. (SI: Lights during presetting. Frequency unit indicators [kHz, MHz] kHz: AM, or PCM sampling frequency MHz: FM Input overload indicator [OVER] Lights when input exceeds rated values. Turn the A/D attenuator on if this occurs frequently (^ page 14). IWI IWI m IWI IWI IWI IWI IWl imi m imi imi i/ni imi imi imi £[£ T~il~c SL N SB srIlfe LOWIMP □ TUNED »SPEAKERS MONO ATT< n B STEREO r-SOUND MODE “i RX DQPRO LOGIC B STEREO SURROUND PCM NEO:6 SFC EH E...