Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Linear, modell DXSR-1508/EC

Hersteller: Linear
Dateigröße: 260.42 kb
Dateiname:

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

ZONES ARE NORMALLY OPEN WITH END-OF-LINE RESISTORS 2. LOW BATTERY AND STATUS OUTPUTS ARE COMBINED TO TRIGGER ZONE 4 AS TROUBLE TO +12 VOLTS TO RECEIVER OUTPUT N.C. N.O. COM 12 VOLT RELAY 1N4001 DIODE EXAMPLE 4-ZONE CONTROL PANEL HOOK-UP EXAMPLE BEEPER HOOK-UP TO RECEIVER OUTPUT TO +12 VOLTS PIEZO BEEPER EXAMPLE L.E.D. HOOK-UP 1K OHM L.E.D. TO +12 VOLTS TO RECEIVER OUTPUT JUMPER IN THIS POSITION (FACTORY SETTING) CAUSES A MOMENTARY 3/4 SECOND OUTPUT WITH EACH ACTIVATION SET OUTPUT JUMPERS FOR EACH CHANNEL USED JUMPER IN THIS POSITION CAUSES A TOGGLE OUTPUT, EACH ACTIVATION WILL CAUSE THE OUTPUT TO SWITCH FROM OFF TO ON, OR, ON TO OFF JUMPER REMOVED CAUSES OUTPUT TO LATCH UNTIL RESET BY A RESTORE TRANSMISSION (DXS-31 DOOR CLOSED) OR RESET BY PRESSING THE CHANNEL BUTTON (JUMPER CAN BE STORED ON SINGLE PIN) CUT STATUS JUMPERS FOR ANY CHANNELS THAT REQUIRE STATUS TRANSMISSION MONITORING USE SMALL CUTTERS TO CUT JUMPERS IF NORMALLY CLOSED OUTPUTS ARE REQUIRED, REMOVE THE OUTPUT POLARITY JUMPER MOMENTARY OUTPUT TOGGLE OUTPUT DOOR & WINDOW LATCHING OUTPUT 1 2 3 4 REMOVE THE PROGRAM JUMPER, THE CHANNEL DISPLAY SHOWS "P" BRIEFLY PRESS THE BUTTON FOR THE CHANNEL THAT THE TRANSMITTER IS GOING TO BE ADDED INTO, THE CHANNEL NUMBER SHOWS ON THE DISPLAY YOU HAVE 5 SECONDS TO ACTIVATE THE TRANSMITTER, THE ALARM LED WILL BLINK AFTER THE TRANSMITTER IS ENTERED, OR AFTER 5 SECONDS, THE CHANNEL DISPLAY WILL RETURN TO "P" REPEAT STEPS 2 & 3 FOR ADDITIONAL TRANSMITTERS (UP TO 32 TOTAL, WITH ANY MIX OF CHANNELS) THEN REPLACE PROGRAM JUMPER WHEN FINISHED NOTE: ON MULTI-BUTTON TRANSMITTERS, EACH BUTTON HAS A UNIQUE CODE, AND IS ADDED TO THE RECEIVER SEPARATELY, INTO ANY CHANNEL 1 2 3 COUNT THE NUMBER OF TIMES THE ALARM LED BLINKS, THIS IS THE NUMBER OF TRANSMITTERS PROGRAMMED INTO THE CHANNEL REPEAT STEPS 2 & 3 TO REVIEW OTHER CHANNELS REPLACE THE PROGRAM JUMPER WHEN FINISHED R&TTE VAEE 27841 SFT, ETS, 89/336/EEC. EMC Linear Corporation declares that the apparatus DXSR-1504/EC and DXSR-1508/EC complies with the essential requirements and other relevant provisions of Directive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his Linear product is warranted against defects in material and workmanship for twelve (12) months. The Warranty Expiration Date is labeled on the product. This warranty extends only to wholesale customers who buy direct from Linear or through Linear’s normal distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part of Linear Corporation for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All implied warranties, including implied warrantie...