Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user’s guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user must correct the interference. CE Mark Warning This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures. All rights reserved. All brand names are registered trademarks of their relative holders. Trademarks Product names mentioned in this manual may be trademarks or registered trademarks of those products and are hereby acknowledged. • Ethernet is a trademark of Xerox Corporation. • Microsoft Windows is a trademark of Microsoft Corporation. Preface This manual describes how to install and use the ClearCube F6151 Media Converter and Chassis System. The system introduced here is capable of housing up to sixteen media converters, each of which offers one channel media conversion solution: • 10/100BaseTX - 100BaseFX • 100BaseTX - 100BaseFX The ClearCube Ethernet Media Converter fully complies with IEEE802.3 10BaseT and IEEE802.3u 100BaseTX/FX standards. In this manual, you will find: • Introduction on the Chassis System • Product features • Illustrative LEDs functions • Installation instructions • Specifications Package Contents When you unpack the product package, you shall find these items listed below. • ClearCube F6151 Media Converter Chassis System, consisting of one chassis with 16 media converters • Two power supplies installed on the chassis • AC power cord • User’s Manual • Accessories: rackmount screws, brackets, & bracket screws • Media converter carriers, fitted to each bay Please inspect the contents, and report any apparent damage or missing items immediately to your authorized reseller. Chassis Overview ClearCube F6151 Media Converter Chassis System Figure 1: Chassis and converters equipped with two power supplies Product Features ¦ HOUSES SIXTEEN MEDIA CONVERTERS ¦ FRONT PANEL LEDS FOR POWER STATUS ¦ STANDARD 19” RACKMOUNTABLE SIZE, 2U ¦ NON-STOP OPERATION & MINIMAL DOWNTIME ¦ HOT-SWAPPABLE The following items are designed to be hot swappable to allow easy and quick replacement: - Media converters - Power supplies with fans ¦ ADEQUATE VENTILATION - Provides one cooling fans on the left and right side - Ventilation holes on each side ¦ POWER REDUNDANCY & POWER ISOLATION Two high quality internal power supplies provided for load- sharing purpose. - Load sharing mechanism: If one power supply should fail, the redundant power supply is capable of taking over immediately - Converter bay power isolation ensures each bay is electrically isolated from each other ¦ OVER CURRENT PROTECTION - Fuses on PCB for each converter bay - Fuse on each power supply Front Panel Display FRONT PANEL The front panel of this ClearCube F6151 Media Converter Chassis System shows it with sixteen media converters in bay 1~16. There are two LED indicators on the left side of the front of the chassis that indicate the status of each power supply. Figure 2: Front panel of ClearCube F6151 Media Converter Chassis System UNDERSTANDING LEDS Power Supply’s Switch LED Green Power switched on Off Power switched off Blown fuse Power supply failed .. Before you use this table for troubleshooting, make sure the chassis system is properly connected to power and switched on. Installation Selecting a Site for the Equipment As with any electric device, you should place the equipment where it will not be subjected to extreme temperatures, humidity, or electromagnetic interference. Specifically, the site you select should meet the following requirements: • The ambient temperature should be between 32 and 104 degrees Fahrenheit (0 to 40 degrees Celsius). • The relative humidity should be less than 90 percent, non-condensing. • Surrounding electrical devices should not exceed the electromagnetic field (RFC) standards for IEC 801-3, Level 2 (3V/M) field strength. • Make sure that the equipment receives adequate ventilation. Do not block the ventilation holes on each side of the switch or the fan exhaust port on the side or rear of the equipment. • The power outlet should be within 1.8 meters of the switch. Deciding How to Install the System The accessories supplied in the product package include: rackmount screws, rackmount brackets, and bracket screws. This well-built chassis can be installed in the following ways: MOUNTED TO 19-INCH STANDARD RACK Use the rackmount brackets and screws to install the chassis into any EIA 19” standard rack. Step 1: Attach the brackets to each side of the chassis. Apply screws to each side and secure them tightly. Step 2: Carefully position the chassis into the rack...