Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Dish Network Dateigröße: 8.7 mb Dateiname: Unterrichtssprache:

15 Chapter 2Chapter 2 Remote Control Types of Remote Controls Remote Control 1 uses infrared (IR) signals to: • Control TV1 menus for the nearby TV in Dual Mode. • Control the satellite receiver in Single Mode. IR signals travel only short distances (60 feet or less), and cannot go through walls or other solid objects. You must point the remote control directly at the receiver, with no objects blocking the line of sight. Remote Control 1 uses IR signals to control the receiver and other devices it is programmed to operate. This remote control is identified by the green number 1 at the bottom of the remote control. 12UHFPRO Remote Control 2 uses UHF Pro signals to: • Control TV2 menus for the remote TVs in Dual Mode. • Control the satellite receiver in Single Mode. UHF Pro signals travel long distances and go through walls and other solid objects. To use Remote Control 2 to control the receiver, you must attach the remote control antenna to the receiver back panel (see page 17). Remote Control 2 uses IR signals to operate other devices programmed into the remote control. You must point the remote control directly at these devices, with no objects blocking the line of sight. This remote control is identified by the blue number 2 at the bottom of the remote control. 16 Satellite ReceiverSatellite Receiver Remote Control Remote Control Batteries The remote control comes with AAA batteries. When you replace old batteries, you should replace all of the batteries. Use batteries of the same kind, for example, alkaline or carbon zinc. Don’t mix batteries of different kinds. Alkaline batteries last longer. 1. Press down on the top of the battery cover and slide the cover off. 2. Take out all of the old batteries. 3. Put the new batteries in. Make sure you match the plus (“+”) ends with the plus markings on the battery case. 4. Slide the cover back into place. Low Battery Warning When you see a low battery warning message on your screen below the Program Banner, the batteries in your remote control are weak and need to be replaced. Remote Battery Low Remote Battery Low Attach the Remote Antenna Attach the remote control antenna to the receiver's back panel REMOTE ANTENNA input so you can use your UHF Pro Remote Control 2. Without the remote control antenna, you cannot use the remote to control the receiver. See Adjusting the Remote Control Antenna on page 73 for more detailed information about improving the performance of your UHF Pro Remote Control 2. 17 Chapter 2Chapter 2 Remote Control Remote Control Buttons SAT Mode To use the features described in this section, make sure you are in SAT mode by pressing the SAT Mode button. SAT Receiver Power & TV Power Menu Program Guide Arrows/Select Buttons View Satellite ProgrammingDigital Video Recorder (DVR) Buttons Picture-In-Picture (PIP) Buttons Number Buttons Top button turns the receiver on/off, bottom button turns the TV on/offProgramming required Channel up/down, navigate through menus/guides and select a desired option Exit out ofany menu/ guide and go back to viewing live TV DISH Explore interactive TV features Browse See what is on other channels while watching TV Enter a desired annel number, or select menu items Search arch for a programWatch two separ programs at once in single mode Recover Recovers satellite programming if your TV input or channel has changed Form Format the picture to the desired width to match the progr you are viewin Display current and future satellite programlistings Page Buttons Page up/down in menus and display options Control TV volume Programming required Access receiver features and settings Themes Search for programs using Themes Recall Go back to last channel viewed Info Display programinformation Pause live TV and play or record programmingVolume & Mute Buttons Press this button for SAT Mode Remote key may be different than shown here 18 Satellite Receiver Remote Control TV Mode To use the features described in this section, make sure you are in TV mode by pressing the TV Mode button. Remote programming is required. Press this button for TV 19 Chapter 2Chapter 2 Remote Control VCR Mode To use the features described in this section, make sure you are in VCR mode by pressing the VCR Mode button. You can use this mode to operate your DVD player instead of a VCR. Remote programming is required. VCR Press this button for Top button on/off, button 20 Satellite ReceiverSatellite Receiver Satellite Receiver Front Panel Satellite Receiver Front Panel TV1 and TV2 Dual and Single Power and Power System Info Smart Card Door Mode Indicators Left light indicates Record Lights Left light indicates Turns receiver power on/off; Mode Switches receiver Displays the System Slot for a future Single Mode, right power is on, right red press and hold between Single Information smart card indicates Dual Mode light indicates recordingto reset receiver and Dual Mode Screen Infrared USB Port Arrows Select Menu Info Sensor/Blaster Connection to Change channels...

Herunterladen

Geben Sie zwei Ziffern: