Stimmen - 5, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
When not in use, place the supplied covers over the jacks by snapping them in place. To remove, gently press on the left side of each cover so that it pivots out. Video Components: Install video components, e.g., game consoles and camcorders, as follows (see Figure 31): • Connect the component’s S-video or composite video output (use only one) to the AVR’s front-panel Input. • Connect the component’s optical or coaxial digital audio output to either the Optical or Coaxial Input on the front panel. Connect an analog device’s audio outputs to the AVR’s front-panel Analog Audio Inputs. 25 INSTALLATION Figure 31 – Connecting a Device to the Front-Panel Inputs Audio Components: Connect audio-only devices, such as CD players, to either the Coaxial or Optical Digital Audio Inputs, or the Analog Audio Inputs (see Figure 31). Step Five – Connect the Video Display IMPORTANT NOTE: Do not connect any video output on the video display (TV) to any video input on the AVR. Doing so will cause undesirable video interference. HDMI Video: If the display has an HDMI input, connect it to the HDMI Monitor Output (see Figure 32). No other video connections are required from the AVR to the video display. Analog video sources (composite, S-video and component) are converted to the HDMI format and upscaled to as much as 1080p resolution, depending on the display’s capabilities. Proceed to Step Six. AVR 3550HD Figure 32 – HDMI Monitor Output Component Video: If the display does not have HDMI inputs, but does have component video inputs, connect the Component Video Monitor Outputs to the display (see Figure 33). The AVR 3550HD converts composite and S-video sources to the component video format, while upscaling the resolution to as high as 1080i, depending on the display’s capabilities. Select the appropriate resolution manually, as described in the Initial Setup section. AVR 3550HD Composite/S-Video: If the video display does not have HDMI or component video inputs, connect the composite or S-video Monitor Output to the display. If available, S-video is preferred over composite video. The AVR 3550HD will convert composite video sources to S-video. See Figure 34. AVR 3550HD Figure 34 – Composite and S-Video Monitor Outputs Consult the manual for your TV to learn how to select the correct video input. Step Six – Plug in AC Power After making all wiring connections, plug each component’s AC power cord into a working outlet. You may plug one device that draws no more than 50 watts into the AC Switched Accessory Outlet. See Figure 35. Turn on the device’s mechanical or master power switch, and it will power on any time the AVR 3550HD is turned on. If the device has a clock or must always be on, do not plug it into this outlet. AVR 3550HD Figure 35 – Switched AC Accessory Outlet Flip the rear-panel Master Power Switch Off before plugging the AC Power Cord into an electrical outlet. This will prevent the possibility of damaging the AVR in case of a transient power surge. The AVR 3550HD is equipped with a detachable power cord, allowing you to fully wire your system before installing the AVR. Plug the male end of the cord into an unswitched AC outlet, and the female end into the AVR 3550HD. See Figure 36. Figure 33 – Component Video Monitor Outputs 26 AVR 3550HD Figure 36 – AC Power Input Step Seven – Insert Batteries in Remote The AVR 3550HD remote control uses four AAA batteries (included). To remove the battery cover located on the back of the remote, squeeze the tab and lift the cover. Insert the batteries as shown in Figure 37, observing the correct polarity. Figure 37 – Remote Battery Compartment Point the remote’s lens toward the front panel of the AVR 3550HD. Make sure no objects, such as furniture, are blocking the remote’s path to the receiver. Bright lights, fluorescent lights and plasma video displays may interfere with the remote’s functioning. The remote has a range of about 20 feet, depending on the lighting conditions. It may be used at an angle of up to 30 degrees to either side of the AVR. Leave the Zone Selector Switch at the bottom in the Zone 1 position for normal use. If the remote seems to operate intermittently, or if pressing a button on the remote does not cause the AVR Settings Button or one of the Source Selectors to light, check or replace the batteries. Step Eight – Program Sources Into the Remote The AVR 3550HD remote may be programmed to control many brands and models of DVD players, cable boxes, satellite receivers, the Harman Kardon DMC 1000 digital media center and TVs. It is also preprogrammed to operate your iPod when docked in The Bridge II. To access the functions for a particular device, switch the remote’s device mode. Press the AVR Settings Button to access the codes that control the receiver, or the Source Selector Buttons to access the codes for the devices programmed into the remote. Follow these steps to program the correct codes for each source device into the remote: INSTALLATION 1. Look up the...