Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: AMC Dateigröße: 517.56 kb Dateiname: Unterrichtssprache:

Fotos und technische Daten  AMC  25100

Do not place the amplifier on a soft surface such as a carpeted surface that may block the ventilation holes of the bottom cover. Also, avoid obstructing the ventilation holes in the top cover. CAUTION: To prevent the risk of fire or shock, do not allow any liquid or moisture to enter into the internal parts of this product. If any liquid accidentally enters this product, shut off the power and remove the AC power cord immediately. If the liquid is anything other than clean water or pure alcohol, have the product examined by a service technician. Servicing of this product should be referred to a qualified service technician. Your AMC amplifier is set to work on your local mains supply voltage. Check that your local mains supply voltage agrees with the voltage setting indicated on the back panel of the amplifier. If not, please contact your dealer or national distributor for details on how to proceed further. The cores of the mains lead are coloured in accordance with the following code: Blue -Neutral Brown -Live Note: Export units for certain markets have moulded majns plugs fitted as standard. As the colours in the mains lead may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked by the letter N, or coloured black or blue. The wire which is coloured brown must be connected to the terminal which is marked by the letter L, or coloured red or brown. 2 REAR PANEL CONNECTIONS/FRONT PANEL CONTROLS REAR PANEL 432 432 432 432 432 1 1 .MAINS INLET 4.LINE INPUTS 2.INPUT LEVEL CONTROLS 5.LOUDSPEAKER TERMINALS 3.LINE OUTPUTS FRONT PANEL or 25100 1 1. POWER SWITCH 3 REAR PANEL CONNECTIONS FRONT PANEL CONTROLS 1. MAINS INLET Connect the AC line cord in to the mains inlet and plug the AC cord plug into a nearby wall outlet that provides the correct AC power line voltage. 2. INPUT LEVEL CONTROLS Each channel of the 2N100-5/25100 has its own, independent level control. Before turning on the 2N100-5/25100 for the first time, make sure that all level controls are set to their fully clockwise position. These controls can be used for various functions. For example, they can be used to match the levels of loudspeakers in a multi-room installation, or to lower the sensitivity of the power amplifier, so that the volume control on pre-amplifier is at a more convenient and usable position. They can also be used to optimise the balance in a stereo system. 3. LINE OUTPUTS Each input has an accompanying line output which will pass the signal onto another amplifier input or other line-level device. 4. LINE INPUTS There are five RCA phono connectors on the back panel that connect to the inputs of each of the power amplifiers. 5. LOUDSPEAKER TERMINALS The 2N100-5/25100 is equipped with binding post type speaker terminals that are desiged to handle the extremely high peak currents that this amplifier is capable of giving. Connections from these terminals to the loudspeakers should be made with heavy-duty wire. Standard wire of 16 gauge or thicker is recommended especially if low impedance loudspeakers are used. 1. POWER SWITCH The press button switch marked power can be used to switch the 2N100-5/25100 on or off. When the 2N100-5/25100 is switched on, the small indicator above the power switch will glow green. 4 SPECIFICATIONS 2N100-5 Rated power into 8 ohm (IHF)..................................................................130 W Rated T.H.D. 20Hz-20KHz.....................................................................0.03 % Clippii g power into 8 ohm......................................................................140 W Dynamic power into 8 ohm.....................................................................210 W Current limit into 0.1 ohm and 1 ohm..................................................30 Amps Damp ng factor..........................................................................................>200 Input sensitivity for 100W output Power into 8 ohm...............................1 Vrms Input npedance......................................................................22K ohm//150pF Frequency response 20Hz-20KHz....................................................+/- 0.3 dB -3dB.........................................................<5Hz/>110KHz Signat to noise ratio "A" WTD (ref. 1W/8 ohm).....................................>100 dB Separation 20KHz..................................................................................>70 dB OTHERS Dimensions (WxHxD)............................................................432x152x330 mm Net weight 2N100-5/25100..................................................................18.6 Kg Shipping weight (2 pieces) 2N100-5/25100........................................39.1 Kg 25100 100 W 0.03 % 110 W 160 W 25 Amps >180 1 Vrms 22 K ohm//150pF +/- 0.3 dB <5Hz/>110KHz >100 dB >70 dB 432x152...

Herunterladen

Geben Sie zwei Ziffern: