Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
The “Green Dot” affixed on cardboard means PHILIPS pays a financial duty to the “Avoidance and Recovery of Packaging Waste” organization. 3 Safety instructions EN Your receiver has been manufactured to meet the appropriate safety standards, but the instructions below must be followed to operate it safely.These instructions must be kept for future reference. - Before connecting the receiver to the mains, check that the mains supply voltage corresponds to the voltage printed on the rear of the receiver. If the mains voltage is different, consult your dealer. - The receiver does not contain any user-serviceable parts.Do not attempt to open it.All maintenance work must be carried out by qualified services centres. - If you disconnect the receiver from the mains, make sure to unplug it from the wall socket and not just from the AC socket at the back of the unit. Children could seriously injure themselves, as the free end of the cable is still live. -It is recommended to unplug the receiver from the mains during lightning storms. -If the power cord is damaged,it must be replaced.Always refer to qualified services centres. -To prevent fire or shock hazard, do not expose the receiver to rain or moisture. - The receiver should be placed on a firm surface, and the ventilation openings must not be covered with items, such as newspapers, table clothes, curtains, etc. - Do not install the receiver near heat sources such as radiators, stoves or other apparatus that produce heat. Protect it from direct sunlight. - When installing the receiver, ensure there is a gap of approximately 2 cm around the receiver to enable air to circulate freely and prevent overheating. -Leave accessible the mains connector at the back of the unit in case emergency shutdown is required. -Do not place any combustible objects on the receiver (candles, etc.). - No objects filled with liquids, such as vases, should be placed on the unit.The receiver shall not be exposed to dripping or splashing. Should this happen, disconnect your receiver from the mains and consult your dealer. -Make sure that children do not place any foreign objects in any of the openings. -For cleaning, use a soft, damp (not wet) cloth. Never use any abrasive cloth and aerosol cleaners. Your receiver, as any electronic equipment, consumes power. In order to reduce power consumption, please switch your receiver to “Low Power” whenever you are not using it. For maximum energy saving we recommend you switch off the receiver by unplugging it from the mains if you are not using it for a long time, e.g. during holidays. 4 Product description EN 4.1 Front panel QWERT Y UIO P 1 button with indicator............................ Standby (short key press) “Low Power” (2-second key press) - indicator lit in red Reset (5-second key press) 2 P-................................................................ Channel down Wake up the receiver from stand-by or “low power”. 3 P+............................................................... Channel up Wake up the receiver from stand-by or “low power”. 4 TV/RADIO.................................................. Toggle between digital TV and digital radio. Wake up the receiver from stand-by or “low power”. 5 HDTV......................................................... Indicate reception of HD programmes when lit in blue. 6 Display ........................................................ Front panel display.See paragraph 4.2. Open the door located on the right-hand side of the receiver front panel to access the following: 7 V-Output..................................................... Switch between output formats (HDMI,YPbPr,or EXT1). 8 V-Format ..................................................... Select picture resolution (Auto,1080i,720p,or 576p). 9 OK.............................................................. Confirm selection. 10 Smart card slot (slot 1) ............................... See chapter 5. 4.2 Front panel display 4.2.1 Pictograms Represents progression of channel scan or volume change. Lit when a recording is running. Lit during storage of data at the end of a channel scan. Lit when a smart card is required. Blinks when receiving a remote control command. Lit when at least one recording or reminder has been programmed. EN 4.2.2 Description of segment display messages Receiver initializing. Please wait. Receiver in stand-by Receiver tuned on a digital TV channel, e.g. Disney Channel. Receiver tuned on a digital Radio channel Recording in progress.To cancel a recording which is in progress press TIMER then 0. The device connected to the EXT2 SCART of your receiver is playing back a recording. Stop playback to return to digital channels. 4.3 Rear panel EN TYIOPREWUP10 11Q 1 RF OUT (*) ................................................ RF output used to connect your receiver to a VCR/TV set to watch analogue channels only, or to connect another receiver 2 RF IN (*)..................................................... RF input used t...