Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
5. Talkover Button - When engaged this function will decrease all signal levels, except the microphone level, by 15dB. A red LED next to the Talkover Button will glow when the talkover function is engaged. In the OFF position all signals will remain at their normal levels. 6a. Microphone Volume - This knob is used to regulate the microphone output volume. Turning the knob in a clockwise direction will increase the volume level. 6b. Microphone EQ Section - These controls are used to adjust the microphone treble level, midrange, and bass levels. Each microphone input has a separate channel EQ. Microphone treble control - This knob is used to adjust the treble levels of the Microphone with a maximum signal gain of 15dB or maximum signal decrease of -30dB. Turning the knob in a counter-clockwise direction will decrease the amount of treble applied to the microphone signal, turning the knob in a clockwise direction will increase the amount of treble applied to microphone signal. Microphone BASS control - This knob is used to adjust the low frequency levels of the microphone with a maximum signal gain of 15dB or maximum signal decrease of -30dB. Turning the knob in a counter-clockwise direction will decrease the amount of bass applied to the microphone signal, turning the knob in a clockwise direction will increase the amount of bass applied to microphone signal. 7. Channel Cut Buttons - These buttons are used to cut out the Treble, Mid or Bass frequencies of the incoming audio signal. When these buttons are depressed the selected frequency level is cut by 100%. When a Cut Button is engaged a red LED located directly above the specific button will begin to glow, indicating the cut function has been activated. Depressing the Cut Button will disengage the cut function. 8. Level Indicators - The dual LED’s indicators are used to indicate either the master output level or the PFL level’s of channels one and two. The level indicators will directly reflect the operating mode of the dB Selector Switch (15). 9. Channel Gain Control - This adjustment is used to adjust an audio source signal input gain for a channel. Never use the gain control to adjust output volume. Setting the gain level properly will ensure a clean output signal. To properly set the gain level controls: 1. Be sure the Master Volume Control (11) is set to minimum (zero output). 2. Set the Channel Fader (2) to level 7. 3. Begin play on an audio source connected to the channel you are adjusting. 4. Be sure the LED Level Indicator Function Switch (15) is set to the PFL CH1/CH2 position. 5. Turn the PFL (4) function on, for the channel you are adjusting. 6. Use the Gain Control (9) to achieve an average output level of +4 dB. 10. Main Power Switch - This is the main power ON/OFF button. The power switch will glow blue when power is ON. Before main power is applied, be sure you have made all connections to the mixer. Also be sure your amplifier(s) is(are) tuned off. Remember to avoid damaging pops, the mixer should be powered on first and turned off last. 11. Master Volume Control - This rotary knob is used to control the master output level (volume). To avoid distorted output try to maintain an average output signal level +4 dB. Be sure this volume control is always set to zero before turning the unit on. Q-D5 MKII™ Controls and Features Cont. ©American Audio® - - Q-D5 MKII™ Instruction Manual Page 6 12. Cue Mixing Controller - This knob selects the channel for monitoring. The monitor signal comes from the Prefader. This means it will not be affected by the channel faders. You can monitor each channel individually. Connect your headphones to the HEADPHONES jack (34). Turn the CUE MIXING CONTROL to CUE and select the desired channels with the PFL switches. When you turn the CUE MIXING CONTROL to PGM (PFL switches without function), you can cue the output signal of the mixer. If the CUE MIXING CONTROL is set to the center position, you can cue both the channel signal you selected and the output signal.With the CUE LEVEL control, you can adjust the phones volume without changing the output signal. 13. Cue Level Volume Control - This knob is used to adjusts the headphone volume output level. Turn the knob in a clockwise direction to increase the headphone volume. 14. Channel Equalizer (“ROTARY KILLS” - Bass/Mid/Treble Control) - All of the channels include a three-band signal EQ. These controls are used to increase or decrease the LOW’s, MID’s, and HI’s of the output signal. CHANNEL treble control - This knob is used to adjust the treble levels of a channel allowing for a maximum treble gain of 15dB or maximum decrease of -30dB. Turning the knob in a counter-clockwise direction will decrease the amount of treble applied to a channel signal, turning the knob in a clockwise direction will increase the amount of treble applied to a channel signal. CHANNEL midrange control - This knob is used to adjust the midrange levels of a channel allowing ...