Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
CHANNEL FADER CURVE ADJUSTMENT - This rotary knob is used to change the way the channel fader will operate. Each of the two channels has a “Curve” adjustment. The curve on the faders adjust from long or short or any variation of the two. The shorter the curve adjustment the sooner full volume will be reached. 32. CROSSFADER CURVE ADJUSTMENT - This rotary knob is used to change the way the crossfader will operate. The crossfader can operate in different modes, “NORMAL CURVE”, “QUICK CURVE” or any variation of the two. (Quick Curve usually used for crabbing). 33. REVERSE FUNCTION SWITCH - Both the crossfader and the channel faders will reverse function when the reverse switch is activated. When reversing the crossfader, channel two of the crossfader will control volume output for fader channel one and channel one of the crossfader will control volume output for channel fader two. When reversing the channel faders, moving the fader in an upwards direction will decrease channel volume and moving the fader in a downwards direction will increase channel volume. 34. HEADPHONE OUTPUT JACK - This jack is used to connect your headphones to the mixer allowing you to monitor the cue source. Use headphones only rated at 8 ohms to 32 ohms. Most DJ headphones are rated at 16 ohm, these are highly recommended. Always be sure the CUE LEVEL VOLUME (13) is set to minimum before you put the headphones on. 31 32 33 34 Q-D5™ Typical Mixer Set-Up C A S S E T T E D E C K T U R N TA B L E PARAMETER TIME PARAMETER RATIO EJECT POWER CUE 1 2 3 4 5 6 7 8 9 0 RELOOP SINGLE LOOP REMAIN NONSTOP ELAPSED TOTAL T M S PROGRAM LOCK KEY BEAT SYNC. F PITCH BPM CUE AUTOB PM OFF ON FX MIX BOP ENTER SKID PHASE FLANGER PAN FX SELECT SGL/CTN TIME REV.PLAY TEMPO LOCK 4%/8%/16% SCRATCH FILTER HOLD ECHO TRANS ON/OFF SAMPLE PITCH T U R N TA B L E ©American Audio® - - Q-D5™ Instruction Manual Page 11 DJ SKILZ SIGNATURE SERIES Q-D5™ Typical Mixer Output Connections Set-Up Speaker Cables RCA to 1/4” Patch Cables ©American Audio® - - Q-D5™ Instruction Manual Page 12 C A S S E T T E D E C K RCA to RCA Patch Cables DJ SKILZ SIGNATURE SERIES Q-D5™ Cleaning Q-D5™ Cleaning 1. Use normal glass cleaner and a soft cloth to wipe down the outside casing. 2. Use a cleaner specially designed for electronics to spray in and around the knobs and switch. This will reduce small particle built up that can effect the proper operation of the mixer. 3. Clean should be carried out every 30-60 days. 4. Always be sure to dry all parts completely before plugging the mixer in. Cleaning frequency depends on the environment in which the mixer operates (i.e. smoke, fog residue, dust, dew). Q-D5™ Cross Fader Replacement The crossfader is “Hot Swappable” which means it may be replaced at any time, even when power is applied. Only replace with American Audio Part OF-1. Replacing with any other model fader may seriously damage your mixer. Replacing the Crossfader (Model OF-1): 1. Carefully remove all the knobs for the controls on the face of the unit, including fader knobs. 2. Using a # 2 Phillips screw driver, unscrew the four screw that secure the in the face plate in place and remove the face plate. 3. Using a number two Phillips screw driver, unscrew the each of the stainless steel retaining screws that hold the crossfader in place. 4. Gently remove the crossfader from its seated position. You may need to wiggle the crossfader slightly to unseat it. 5. After removing the crossfader, disconnect the ribbon cable that attaches the crossfader to the PC board. Grasp the crossfader by its base and pull the ribbon cable by its connector not the actual cables. The connector is designed to fit one way, so don’t worry about the connectors orientation. 6. Connect the new crossfader (model OF-1 only) to the ribbon cable. 7. Reassemble in reverse order. Changing/Replacing the Transformer Switch: 1. Follow steps one and two above to remove the faceplate. 2. Disconnect the mixer’s main power supply. 3. Using a number two Phillips screw driver, unscrew each of the larger retainer screws that hold the transformer switch in place. 4. To replace: disconnect the ribbon cable that attaches the switch to the PC board. Grasp the crossfader by its base and pull the ribbon cable by its connector not the actual cable. The connector is designed to fit one way, so don’t worry about the connectors orientation. 5. To augment transformer orientation: Pull the switch out and turn to the desired position. 6. Reassemble in reverse order. ©American Audio® --Q-D5™ Instruction Manual Page 13 Q-D5™ Registration Q-D5™ Registration pany a return authorization (R.A.) number. The R.A. number must be clearly written on the outside of the return package. A brief description of the problem as well as the R.A. number must also be written down on a piece of paper and included in the shipping container. If the unit is under warranty, you must provide a copy of your proof...