Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
................ ............ ................ ......,...... .. ..... • . . . . . . . . . . . . . . . . . . . . . . . . . ..... • ............... .. .... • ................. ....... .... • ................. ....,...... .. .. • . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ( . . ) . . . . . , . . . . . . . . .... • ...........,........ .........,.............. ..... • ...., .....,...... .. • ................. ..... ........................ .............. ... • .............,....... ......... ............. ... • ................ ..... ................ ....... ........ FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The Class A limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense. N This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with the unit to ensure compliance with FCC emissions limits. Quick Start Guide — FOX HD-SDI FOX HD-SDI • Quick Start Guide QS-1 N The FOX HD-SDI is a transceiver that can function as a transmitter and/or a receiver. At least two units are required for a transmitter-receiver system with at least one fiber optic cable linking each two units. The FOX HD-SDI is available in single mode or multimode versions. Connect and operate two or more FOX HD-SDI units as follows: Step 1 Power off all equipment. If desired, mount the units in racks. Step 2 Use the rear panel Mode DIP switches to configure each unit to be installed in the system as a bidirectional transceiver, a transmitter, or a receiver as shown above right. N The drawings below and on QS-2 show the signal flow for the three different FOX HD-SDI configurations. For more information on the various modes and their capabilities, see "Transceiver configurations" in chapter 1, "Introduction". Step 3 Transmitting unit — Connect an HD-SDI, SDI, or 3G-SDI video source to the unit's HD/SDI In BNC connector. Step 4 Transmitting unit — If the FOX HD-SDI is configured as a transmitter, and if desired, connect one or two local monitors to the unit's Buffered Outputs BNC connectors. These two BNCs output the same HD-SDI, SDI, or 3G-SDI video that was input in step 3. Step 5 Both units — Connect a fiber cable between the transmitting unit's Optical Tx connector and the receiving unit's Optical Rx connector. MODE MODE Bidirectional Transceiver 1 down 2 down 1 down 2 up Transmitter 1 2 1 2 MODE 1 up 2 down Receiver with Loop-through 1 2 HD/SDI IN 12V 0.3A MAX FOX HDSDI HD/SDI IN POWER BUFFERED OUTPUTS MODE OPTICAL Tx Rx 1 2 Transmitter Video Source To Receiver Video from Source OPTICAL Rx Tx OPTICAL Rx Tx Table of Contents Quick Start Guide — FOX HD-SDI, cont’d FOX HD-SDI • Quick Start Guide FOX HD-SDI • Table of Contents QS-2 Step 6 Receiving unit — Connect one or two monitors to the unit's Buffered Outputs BNC connectors. Unit configured as bidirectional transceiver — Both BNCs output the HD-SDI, SDI, or 3G-SDI video that was transmitted across the fiber cable. Unit configured as receiver — Output 2 BNC only outputs the transmitted video. Step 7 Receiving unit — If desired, connect a fiber cable between the receiving unit's Optical Tx connector and another unit's Optical Rx connector. Unit configured as bidirectional transceiver — Connect the fiber cable to the transmitting unit. Unit configured as a receiver — Connect the fiber cable to another receiving unit for daisy chaining. N Up to 10 receivers can be daisy-chained in this manner. Step 8 Receiving unit configured as bidirectional transceiver — Connect a video source to the unit's HD/SDI In BNC connector. Step 9 Transmitting unit configured as a bidirectional transceiver — Connect one or two local monitors to the unit's Buffered Outputs BNC connectors. These two BNCs output the same video that was input in step 8. Step 10 Connect power to all FOX units and to all connected video sources and displays. 12V 0.3A MAX FOX HDSDI HD/SDI IN POWER BUFFERED OUTPUTS MODE OPTICAL Tx Rx 1 2 Video Source To/from 2nd Transceiver Video from 2nd Transceiver Bidirectional Transceiver 12V 0.3A MAX FOX HDSDI HD/SDI IN POWER BUFFERED OUTPUTS MODE OPTICAL Tx Rx 1 2 Video from Transmitter Transmitter Source Daisy-chained Receiver Receiver with Loop-through...