Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
Unity Video input Number/signal type..................... 1 set of proprietary analog signals Connectors..................................... 1 female RJ-45 Video output Number/signal type..................... 1 RGBHV, RGBS, component video (bi-level and tri-level), S-video, composite video (follows input type) Connectors MTP U R RSA SEQ............ 1 female 15-pin HD for RGB 3 BNC female for Y, R-Y, B-Y (1) 4-pin mini DIN for S-video (Y/C) 1 BNC female for composite video All other models................ 1 female 15-pin HD for RGB or Y, R-Y, B-Y (1) 4-pin mini DIN for S-video (Y/C) 1 BNC female for composite video Nominal level................................ 1 Vp-p for Y of component video and S-video, and for composite video 0.7 Vp-p for RGB and for R-Y and B-Y of component video 0.3 Vp-p for C of S-video Minimum/maximum levels........ 0.8 V to 1.2 Vp-p Impedance...................................... 75 ohms (during video output only) Return loss...................................... <-30 dB @ 5 MHz (during video output only) DC offset......................................... <±20 mV with input at 0 offset Maximum resolution.................... 1920x1200 Refer to the user's manual for the maximum distances recommended for specific resolutions. ebn Sync Output type.................................... RGBHV, RGBS Standards........................................ NTSC 3.58, NTSC 4.43, PAL, SECAM Output level................................... 4.0 V to 5.0 Vp-p, unterminated Output impedance........................ 87 ohms (24 mA) Polarity............................................ Positive or negative (selectable) Audio— MTP U R RSA SEQ, MTP U R A Gain................................................. Unbalanced output: 0 dB; balanced output: +6 dB Frequency response...................... 20 Hz to 20 kHz, ±1 dB (for DC coupling, with jumpers 4 and 5 installed) THD + Noise.................................. 0.15% @ 1 kHz, 0.3% @ 20 kHz at nominal level S/N.................................................. >70 dB at maximum output (unweighted) Audio input— MTP U R RSA SEQ, MTP U R A — See MTP Series transmitters' audio output specifications Number/signal type..................... 1 set of proprietary analog signals Connectors..................................... 1 female RJ-45 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV « 2 dBu dsN Audio output— MTP U R RSA SEQ, MTP U R A Number/signal type..........................................2 mono, balanced/unbalanced Connectors..........................................................................(1) 3.5 mm captive screw connector, 5 pole Impedance............................................................................50 ohms unbalanced, 100 ohms balanced Gain error..............................................................................±1 dB channel to channel Extron MTP U R Series Universal Mini Twisted Pair Receivers • Specifications 1 Specifications — MTP U R Series Receivers, cont'd Control/remote — external device (pass-through, unidirectional or bidirectional) (MTP U R RSA SEQ, MTP U R RS SEQ, or MTP U R RS) Serial control port input/output. RS-232 via (1) 3.5 mm, 3 pole captive screw connector The serial communications link of an MTP U R RSA SEQ, MTP U R RS SEQ, or MTP U R RS is unidirectional only, transmitter to receiver, unless the receiver's internal switch has been set. Baud rates....................................... Up to 38400 bps at up to 500' (152 m) (Higher data rates and distances are possible. Performance varies based on baud rate and cable length.) Protocol........................................... Data bits = 5 - 8 Stop bits = 1 or 2 Parity = odd, even, none Flow control = XON, XOFF, none Protocol is mirrored between the transmitter and the receiver. Serial control pin configurations. Captive screw connectors: 1 = TX, 2 = RX, 3 = GND General Recommended cable type............ CAT5/E/6 (shielded or unshielded) External power supply................. 100 VAC to 240 VAC, 50/60 Hz, external; to 12 VDC, 2 A, regulated Power input requirements........... 12 VDC, 0.5 A Temperature/humidity................ Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing Cooling........................................... Convection, no vents Mounting Rack mount........................ Yes, with optional 1U, 9.5" deep rack shelf, part #60-190-01 (RSU 129) or #60-604-01 (RSB 129); or VersaTools® 1U, 3.5" deep rack shelf, part #60-190-20 (RSF 123) or #60-604-20 (RSB 123) Furniture mount................ Yes, with optional Mini Under-Desk Mounting Kit, part #70-212-01 (MBU 123) Pole mount......................... Yes, with optional projector mounting kit, part #70-217-01 (PMK 100) Enclosure type............................... Metal Enclosure dimensions................... 1.7" H x 4.3" W x 3.0" D (1U high, q...