Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
Unity Number/signal type..................... 1 set of proprietary analog signals Connectors..................................... 1 female RJ-45 Video input and loop through — transmitter Number/signal type..................... 1 analog RGBHV, RGBS, RGsB, RsGsBs, component video (with bi-level or tri-level sync), S-video, or composite video 1 buffered RGBHV, RGBS, RGsB, RsGsBs local monitor loop through (includes ID bits) Connectors..................................... 2 female 15-pin HD Nominal level................................ 1 Vp-p for Y of component video and S-video, and for composite video 0.7 Vp-p for RGB and for R-Y and B-Y of component video 0.3 Vp-p for C of S-video Minimum/maximum levels........ 0.3 V to 1.45 Vp-p Impedance..................................... 75 ohms Horizontal frequency.................... 15 kHz to 130 kHz Vertical frequency.......................... 30 Hz to 150 Hz Return loss..................................... <-30 dB @ 5 MHz DC offset (max. allowable)........... 250 mV Video output — receivers (MTP RL 15HD RS, MTP RL 15HD RS SEQ) Number/signal type..................... 1 set of proprietary analog signals 1 analog RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, or composite video Connectors..................................... 1 female RJ-45 1 female 15-pin HD Nominal level................................ 1 Vp-p for Y of component video and S-video, and for composite video 0.7 Vp-p for RGB and for R-Y and B-Y of component video 0.3 Vp-p for C of S-video Minimum/maximum levels........ 0.3 V to 1.45 Vp-p Impedance...................................... 75 ohms Return loss...................................... <-30 dB @ 5 MHz DC offset......................................... <±20 mV with input at 0 offset Maximum resolution.................... 1920x1200 Refer to the user's manual for the maximum distances recommended for specific resolutions. Sync Input type (transmitter) ............... Output type (receivers)................ Standards........................................ Input level (transmitter) .............. Output level (receivers)................ Input impedance (transmitters) . Output impedance (receivers) .... Max. input voltage ....................... Polarity Transmitters....................... Receivers ............................ Extron MTP 15HD RS Series • Specifications 1 RGBHV, RGBS, RGsB, RsGsBs, bi-level or tri-level for component video RGBHV, RGBS, RGsB, RsGsBs NTSC 3.58, NTSC 4.43, PAL, SECAM 3.5 V to 5.5 Vp-p, unterminated 0.3 Vp-p for component video (bi-level sync) 0.6 Vp-p for component video (tri-level sync) TTL: 4.0 V to 5.0 V p-p, unterminated for RGBHV, RGBS 510 ohms 110 ohms 5.5 Vp-p Positive or negative (follows input polarity) Positive or negative (switch selectable) Specifications — MTP 15HD RS Series, cont'd Control/remote — external device (pass-through, unidirectional or bidirectional) Serial control port input/output MTP T 15HD RS................................RS-232 via (1) 3.5 mm, 3 pole captive screw connector Receivers........................................................1 set of proprietary signals on a female RJ-45 jack Serial control port output/input MTP T 15HD RS................................1 set of proprietary signals on a female RJ-45 jack Receivers........................................................RS-232 via (1) 3.5 mm, 3 pole captive screw connector The serial communications link of an MTP RL 15HD RS or an MTP RL 15HD RS SEQ is unidirectional only, transmitter to receiver, unless the receiver's directional jumper has been repositioned. The jumper should be repositioned only when the receiver is the only one in the system. Baud rates...................................... Up to 38400 bps at up to 600' (183 m) (Higher data rates and distances are possible. Performance will vary based on baud rate and cable length.) Protocol.......................................... Data bits = 5 - 8 Stop bits = 1 or 2 Parity = odd, even, none Flow control = XON, XOFF, none Protocol is mirrored between the transmitter and the receiver. Serial control pin configurations. Captive screw connector: 1 = TX, 2 = RX, 3 = GND General Recommended cable type............ CAT 5/5E/6 (shielded or unshielded) External power supply................. 100 VAC to 240 VAC, 50/60 Hz, external; to 12 VDC, 2 A, regulated Power input requirements........... 12 VDC, 0.5 A Temperature/humidity................ Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing Cooling........................................... Convection, no vents Mounting Rack mount........................ Yes, with optional 1U, 9.5" deep rack shelf (RSU 129, #60-190-01 or RSB 129, #60-604-01); 1U, 6" deep rack shelf (RSU 126, #60-190-10 or RSB 126, #60-604-10); or VersaTools® 1U, 3.5" deep rack shelf (RSF 123, #60-190-20 or...