Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
From the front panel press Menu repeatedly until you leave the menu system UP/DOWN ARROWS -Once you are in the menu system, use the UP/DOWN ARROWS to move to the desired menu selection. With the supplied SR10.1 remote, rocking the thumb pad forward and backwards act as the up and down arrows.The current active menu line is highlighted in a contrasting color in the On-screen display and also shown on the front panel display. SELECT / ENTER -Some menu selections select another menu level to be activated. Use the UP/DOWN ARROWS to move to the desired menu line. Pressing SEL or ENTER will activate the next menu. With the supplied SR10.1 remote, pressing on the center of the thumb pad also acts as the ENTER key. NUMERIC KEY DIRECT ENTRY (remote only) -From the remote control you may also go directly to a menu line by typing the corresponding line number. If there is another menu level below that line it will be activated immediately (no ENTER required). LEFT / RIGHT ARROWS (remote) or Volume Knob (front panel) -To change menu parameters, press the LEFT or RIGHT arrows to change the setting. There are no LEFT or RIGHT arrows on the front panel. The volume knob acts as the LEFT or RIGHT arrows. With the supplied SR10.1 remote, rocking the thumb pad left and right act as the left and right arrows. TEXT EDITING -Some menu selections will allow you to edit text. Use the UP/DOWN ARROWS to change the current (blinking) character. Use the LEFT/RIGHT ARROWS (or VOLUME KNOB) to move to another character position. Additionally, while in the edit text mode, a successive press of a numeric key allows direct recall of the alphanumeric character map. It will allow a step through selecting between numbers, letters and/or symbols. The selection options for each of the numeric keys are as follows: 0 = [-, +, /, ?, space, 0] 4 = [J, K, L, j, k, l, 4] 8 = [V, W, X, v,w, x, 8] 1 = [A, B, C, a, b, c, 1] 5 = [M, N, O, m, n, o, 5] 9 = [Y, Z, y, z, 9] 2 = [D, E, F, d, e, f, 2] 6 = [P, Q, R, p, q, r, 6] 3 = [G, H, I, g, h, i, 3] 7 = [S, T, U, s, t, u, 7] MENU SYSTEM SETUP MENU SYSTEM SETUP S The main menu descriptions are accompanied by the On Screen Menu layout below. In some cases, the front panel will display a slightly abbreviated version of what the On Screen Menu shows due to character space limitations. The On Screen Menu is accessible from the component video output, the Zone A S-video output and the Zone A composite video output. B&K recommends using the On Screen Menu for adjusting unit parameters. The On Screen Menu is not available in Zone B. On Screen Menu Format MMAAIINN MMEENNUU 11 SSyysstteemm SSeettuupp 22 UUnniitt IInnffoorrmmaattiioonn 44 ZZ22 OOppeerraattiioonn 22nndd ZZoonnee ^^vv nneexxtt iitteemm EENNTT sseelleecctt MMEENNUU eexxiitt mmeennuu ssyysstteemm 33 ZZ11 OOppeerraattiioonn TThheeaatteerr Front Panel Menu Format 1 System Setup -System setup should be used when initially setting up the receiver, or if system parameters need to be adjusted. Page 24. 2 Unit Information - Contains information about the unit make, model, serial number, software version, BKC-DIP version, phase locked loop chip version. This information may be needed when contacting customer service. Page 32. 3 Z1 Operation-Theater -Allows viewing and changing the entire state of Zone A. See Unit Operation page 41. 4 Z2 Operation-2nd Zone -Allows viewing and changing the entire state of Zone B. See Unit Operation page 41. MENU SYSTEM SETUP MENU SYSTEM SETUP S SSY YYS SST TTE EEM MM S SSE EET TTU UUP PP 1 11 S SSp ppe eea aak kke eer rrs ss 2 22 I IIn nnp ppu uut tts ss 3 33 P PPr rre ees sse eet tts ss 4 44 D DDi iis ssp ppl lla aay yys ss 5 55 M MMu uus ssi iic cc M MMo ood dde ees ss 6 66 M MMe eem mmo oor rry yy B BBa aac cck kku uup pp/ //R RRe ees sst tto oor rre ee 7 77 A AAd ddv vva aan nnc cce eed dd ^ ^^v vv n nne eex xxt tt i iit tte eem mm E EEN NNT TT s sse eel lle eec cct tt M MME EEN NNU UU m mma aai iin nn m mme een nnu uu 1. Setup Speakers This menu configures the receiver for the number of speakers, speaker size, and location of the speakers in the room. It also contains room equalization options that can optimize the sound for a particular room. The overall sound quality of your system will depend upon how the parameters of this menu are setup. It is very important that the speaker setup is performed when the receiver is initially installed or if any speakers are moved or changed. Page 25. 2. Setup Inputs This menu configures the receiver for the audio/video source devices that are connected to the system. This setup should be performed when the system is initially installed and whenever source components are added or removed. Setup inputs also describes the various audio modes and how each input is configured when it is selected. See page 29. 3. Setup Presets This menu configures the receiver for how the presets will operate and be recalled. Presets allow virtual “snapshots” of the current settings to be saved. The presets can t...
Dieses Handbuch ist für folgende Modelle:Receiver und Verstärker - AVR507 SERIES 2 (6.28 mb)