Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
A Install Guide About this Manual This document covers the MIL-170TRM media converter module. The terms “MIL-170,” MIL-170TRM,” and “converter” are used throughout this document to describe the MIL-170TRM. Introduction The MIL-170TRM is one of a series of modules designed to be installed into Digi's Media Conversion System. This half-/full-duplex device converts optical signals to electrical and vice-versa. The device has a signal capability of transmitting up to 15 km (subject to fiber budget and collision domain restrictions). This module also has the Link Sentry feature. Features • One RJ-45 (UTP) connector • One single-mode, ST connector • Link Sentry feature • Diagnostic LEDs • Management ready–supplied by the optional SNMP modules (MIL-4650 and MIL-4655) • Power supply equipped on the rack mount chassis Installation Do the following to install the MIL-170TRM into a redundant rack mount chassis: 1. Make any configuration changes to the module (i.e., DIP switch settings). 2. Remove the screws securing the faceplate and remove it from the chassis. 3. Slide the module into the slot through the guide rails. 4. Insert the module into the card-edge connector (port bay). Make sure it is seated firmly. 5. Secure the module with the two thumbscrews located on the faceplate of the unit. The unit is now ready for network connections. Model: MIL-170TRM Install Guide MDI-X/MDI Switch The MDI-X/MDI switch allows for quick configuration of the 10BASE-T port. Cables used when the switch is in the MDI-X position (the “left” position): • For a hub/repeater, use a swap cable (pins are connected 1 to 3, 2 to 6, 3 to 1, and 6 to 2) • For a workstation/PC, use a straight-through cable (pins are connected 1 to 1, 2 to 2, 3 to 3, and 6 to 6) MDI-X/MDI Switch RJ-45 Female Connector 4 3 2 1 LEDs (4 total) 4-pin DIP Switch ST-Type Connectors Figure 1.Inside of the MIL-170TRM Cables used when the switch is in the MDI position (the “right” position): • For a hub/repeater, use a straight-through cable (pins are connected 1 to 1, 2 to 2, 3 to 3, and 6 to 6) • For a workstation/PC port, use a swap cable (pins are connected 1 to 3, 2 to 6, 3 to 1, and 6 to 2) Link Sentry Configuration The Link Sentry feature on the MIL-170TRM is configured through a 4-position DIP switch (refer to Figure 1). Default setting for the DIP switches: All switches are in the “up” position. Link Sentry allows users to add new management tools to the network. When enabled, it monitors the selected receiver port and, if the Link test signal is not seen, the unit will stop sending a signal through the selected transmit port. Model: MIL-170TRM Install Guide The following table shows which Link Sentry feature is enabled: Table 1: Link Sentry Features Switch Losing Link on RX of Stop sending Link on TX of 1 (down) Fiber port Fiber port 2 (down) UTP port UTP port 3 (down) UTP port Fiber port 4 (down) Fiber port UTP port Note: For two MIL-170s used back-to-back and UTP-to-UTP, all DIP switches must be enabled (in the “down” position) on the first MIL-170. On the second MIL-170, enable switches 1 and 4 (in the “down” position). Default setting for Link Sentry: All switches set in the “up” position (disabled). When using the SNMP module to control the Link Sentry feature, leave the switches in the default mode (“up”). Indicators There are four LEDs, including: TP/ACT: Receiving packets from the 10BASE-T port TP/LINK: There is an active connection on the 10BASE-T port FX/LINK: There is an active connection on the 10BASE-FL port FX/ACT: Receiving packets from the 10BASE-FL port Specifications RJ-45: MDI • Pin 1 = Transmit Data + • Pin 2 = Transmit Data • Pin 3 = Receive Data + • Pin 6 = Receive Data RJ- 45: MDI-X • Pin 1 = Receive Data + • Pin 2 = Receive Data • Pin 3 = Transmit Data + • Pin 6 = Transmit Data Model: MIL-170TRM Install Guide 1234 5 78 6 Figure 2.RJ-45 Pinouts Fiber Specifications: ST connector • 1300 nm single-mode fiber • 8 or 9/125 m m single-mode fiber • Launch power: -19 dBm • Receive sensitivity: -36 dBm Operating Conditions Table 2: Recommended Operation Conditions Parameters Minimum Maximum Operating Temperature +5° C +50° C Humidity: Non-condensing 10% 95% Signal Output Load 35 ohm 75 ohm Supply Voltage 4.75 V 5.25 V Model: MIL-170TRM Legal Declaration Regulatory Approvals • FCC Class A • UL 1950 • CSA 22 No. 950 • EN60950 • CE – EN55022 Class B – EN50082-1 Canadian EMI Notice This Class A digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numerique de la classe A respecte toutes les exigences du Reglement sur le materiel brouilleur du Canada. European Notice Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the commission of the European Community. Compliance with these directives implies conformity to the following European Norms: • EN55022 (CISPR 22) - Radio Frequency Interference • EN50082-1 (IEC801...