Stimmen - 5, Durchschnittliche Bewertung: 4.4
(
)
)
|
Anleitung Zusammenfassung
Install/Replace backup Battery The iH41 uses a CR2032 battery for backup battery system to provide continuous alarm operation and clock settings in the event of a power failure. If the Backup Battery has been installed and a power failure occurs or the AC cord is accidentally disconnected, the display backlight will not remain lit, but current time and alarm time settings will be temporarily maintained. Otherwise, you must reset the time and alarm settings. 1. Please make sure the AC adaptor is connected. Otherwise all settings may be lost during battery replacement. 2. Open backup battery compartment door located on the back of the unit. 3. Insert a new CR2032 battery, checking that the polarity (+ and – ends of the battery) matches the drawing near the battery compartment. Close the compartment door. Note: Make sure you dispose of batteries properly (see your local regulations). 3 Using the iH41 Setting Clock 1. Set the DST Switch located on the back of the unit to +1 to add one hour or to -1 to subtract an hour. When set to +1 the DST icon will appear. 2. Press and hold the Clock Adj Button located on the back of the unit until the display flashes. Press the Hour and/or Minute Button to set the time. Hold the button for a few seconds to adjust rapidly. Remember to set the correct AM or PM. An icon below the time digits is the PM Indicator. 3. Press the Clock Adj Button again (or no button within 10 seconds) to exit the clock setting mode. Using the Alarm Setting the Alarm 1. Press and hold the Alarm Button until the alarm time flashes. Press the Hour and/or Minute Button to set the alarm time. Hold the button for a few seconds to adjust rapidly. Remember to set the correct AM or PM. 2. The alarm will automatically arm after set alarm time and the alarm icon will stay on to indicate alarm is armed. 3. Default alarm sound is iPod but if no iPod is docked or iPod cannot play for some reason or the playing sound level is too low, it will automatically switch to buzzer alarm. Arming and Disarming Alarm (Turn Alarm Function On and Off) 1. Once alarm is armed, press the Alarm Button to disarm it. 2. Press the button again to arm the alarm again. Resetting the Alarm to Come on the Next Day When the alarm is sounding, press the Alarm Reset/Power On/Off Button to stop the alarm and reset it to come on the following day at the same time. Snooze Press the Snooze/Dimmer Button after the alarm sounds. The alarm will be silenced and come on again about 9 minutes later. Snooze can be pressed several times during the 1 hour alarm cycle. Sure Alarm The iH41 has a sure alarm feature so if a backup battery is installed, the buzzer alarm will still sound in the event of power failure. 4 Using the iH41 Charging your iPod Note: Please make sure you are using the correct inset for your iPod (see Install iPod Insert) and that it is properly docked into the iH41. Failure to do so may damage your iPod. While your iPod is docked in the unit and the unit is connected to AC power, it recharges (until fully charged). Listening to iPod 1. Dock the already playing iPod, the iH41 will automatically turn on and you will hear the music playing from your iPod. Note: If the volume is too low on the iPod, iH41 may not detect iPod is in play mode. Press the Power Button on the main unit once or Play/Pause Button to play it. 2. When the iPod is docked and in standby mode, press the Play/Pause Button on main unit to play it. The iPod icon on the display will turn on to show it is power on. 3. Press the iPod Play/Pause Button to pause play; press again to resume it. 4. Press the and Button to adjust the system volume. 5. Press or Button on remote control to go to the next or previous track. Press and hold while track is playing for high speed forward or reverse music search of the current track. 6. You can rotate the unit for viewing video, the iH41 display also will change to fit your view orientation too. 7. To turn off the unit, press the Button on the main unit or remote control. Your iPod will continue charging while in the dock. Listening to non-docking iPod or other portable audio devices If you are using an iPod without a docking port or other MP3 player or other portable audio device, you can play it through the iH41 via the Aux-in Jack. 1. Plug one end of an audio patch cord (available at ) into the headphone or line-out jack on your device and the other end of the patch cord into the iH41 Aux-in Jack, located on the back of the unit. 2. Press the to turn the iH41 on. 3. Press the or Button on the main unit or on the remote control to adjust the system volume. You may need to adjust your device volume too. 4. To turn off the unit, press the Power Button. Please remember to turn off your device, too. Watching Videos (iPod models with Horizontal Video Mode) 1. Select a video file on your iPod and press play. 2. Gently turn the unit with docked iPod on its left side. The clock display will adjust to the new orientation. 3. Pr...