Stimmen - 5, Durchschnittliche Bewertung: 4.2
(
)
)
|
Anleitung Zusammenfassung
Install failsafe mechanisms, perform redundancy checks and periodic inspections and adopt other appropriate safety measures when it is necessary. This manual uses the following symbols to ensure safe operation of this timer. ^ WARNING yVam'n9s are indicated when mishandling this product might result in death or serious injury ArAIITION Cautions are indicated when mishandling this product might result in minor injury to the user, vmu i ivn or on|y physical damage to the timer. A WARNING • Note this incorrect wiring of this product can damage it and lead to other hazards. Make sure the product has been correctly wired before turning the power ON. • Before wiring, or removing / mounting the product, be sure to turn the power OFF. Failure to do so might cause electric shock. • Do not touch electrically charged parts such as the power terminals. Doing so might cause electric shock. • Do not disassemble the product. Doing so might cause electric shock or faulty operation. A CAUTION • Use the product within the operating ranges recommended in the specification (temperature, humidity, voltage, shock, mounting direction, atmosphere and etc.). Failure to do so might cause fire or faulty operation. • Firmly tighten the wires to the socket. Insufficient tightening of the wires to the socket might cause fire. SAFETY PRECAUTION Operating voltage Allowable operating voltage range_ Rated frequency Contact rating Reset time Power consumption Life Ambient temperature Ambient humidity Weight SPECIFICATIONS AC/DC : 12-48V/AC/DC : 100-240V NAMES AND FUNCTIONS OF FACEPLATE 85 ~ 110% of rated operating voltage 50/60Hz 250VAC 5A (Resistive load) MAX 0.1s Approx. 2.5VA Mechanical : 5,000,000 times / Electrical : 100,000 times -10~+50°C MAX 85% RH Approx. 120g(H5CLR) / 150g(ASY-4DR) LEDs- RUN: Timing indicator OUT: Control output indicator K/P: Key protection indicator RESET: Reset indicator START: Start indicator GATE: Gate indicator h: Time unit display (Hour) m: Time unit display (Minute) s: Time unit display (Second) □ key :- Reset the output or save the value of setting.(after save than back to the operation mode) Upper display Display PV values (current time, etc.) or setup items. Lower display Display SV values (set time, etc.) and other parameter values. □ key: Performing arithmetic shift operations and switches the display. Hold down for at least 3 seconds to enter setting modes. □□key: Used for Incrementing or decrementing numeric values. SETTING PROCEDURE POWER ON SPECIAL FUNCTION KEY PRESS FOR 3s (1)Stop □ □ Switch ON/OFF Key protection □ 5 Reset PRESS FOR 3a El D Switch to input setting mode OUTPUT TIME u □□ f Select output time ■ / Hold Y-Y 1S •2 0.1s Y-S 5s •3 0.5s Y-6 10s v-1 15s v-fl 20s $ Not functionable on MODE C,D,E and F (2)Timing FOR 3s TIME RANGE Switch to input setting mode S □ Zfl Switch to input setting mode Switch to input signal time setting mode □ or ES Save and back to the operation mode ! □ □ f Select the time range I- I i-3 1-3 /-V /-5 999.9m 1-3 99m59s /-£ 9999m !-R 99h59m /- 7 999.9h 1-8 9999h INPUT SIGNAL TIME □□ Select input Switch to count up/down setting mode | Save and back to the operation mode signal time UP/DOWN MODE Switch to key protection level setting mode KEY PROTECTION LEVEL • I 20ms ■I 1ms □ * Not available for ASY-4DRD and H5CLR-8 5 Save and back to the operation mode ¿-(Countup f í-í Countdown Select count up or count down j~l QQ OUTPUT MODE Switch to output setting mode Save and back to the operation mode Select key protection level Switch to output contact setting mode •1 Lock function key □ ■c’ Lock reset key □ ■3 Lock preset value keyDQ ■i Lock all key □ or 5 back to the operation mode Select output mode 3-/ Mode A 3-5 Mode B 3-9 Mode D 3-s ModeAl 3-fi Mode B1 3-fl ModeE 3-3 Mode A2 3-1 Mode B2 3-t Mode F 3-v Mode A3 3-fl ModeC Seereverse % Mode A1,A2PA3,B1,B2,C,D and F are not available on ASY-4DRD and H5CLR-8 □ OUTPUT CONTACT I 1 □□ Select output contact Switch to output time setting mode Save and back to the operation mode Switch to time range setting mode ■ / 2C ■i 1A1C □ $ Available on H5CLR-8/-11 and ASY-4DRD type only or B Save and back to the operation mode H5CLR-8 H5CLR-8G CONNECTION H5CLR-11 H5CLR-11M Secure online ordering 24/7/365 from electronics MANUFACTURING COMPANY International Headquarters: ?07 Dayton Road - PO Box 1040 • Ottawa. IL 61350 USA 815-433-5100 Fax 815-433-5104 www bb-efec com orders@bb-eleccom suppon@bb-elec.com European Headquarters: Westlmk Commercial Park • Oranmore Co Galway - Ireland +353 91 792444 Fax+35391 792445 wwwbb-europe.com orders@bb-europe com support@bb-europecom 2 TECO Timer User Manual [A : Signal ON delay ij (Timer resets when power comes ON.) SOURCE • Start signal • Gale • Reset - Control output - Set value • UP 0 • Set value DOWN I......—I ! I n! ! ! ü ! I P ! -| ¡I...