Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
MAX/MIN HUMIDITY MAX/MIN SET DOWN(—) WAVE °C/ °F UP(+) RE-SYNC SELECT RESET CLEAR ™. 1579406832ABMain unit RESET SELECT TEST °C/ °F RESET SELECT TEST °C/ °F RESET SELECT TEST °C/ °F RESET SELECT TEST °C/ °F FCDE ™ . Sub-unit Operation Guide DQR-300U 2 •A sticker is affixed to the glass of this clock when you purchase it. Be sure to remove the sticker before using the clock. • Depending on the clock model, the configuration of your clock may differ somewhat from that shown in the illustration. Alarm Off Alarm On •In locations subject to radio frequency interference, the product may malfunction and require you to reset the product. Alarm on indicatorPM indicator Wave OK indicator Antenna Icon Current Humidity Upcomimg weather indicator Current time (Hour, minutes, seconds) Day of the week DATE (month - date) Current Temperature Snooze on indicator Alarm time GENERAL GUIDE Main unit 1SNOOZE/LIGHT button •Press this button to illuminate the display for about four seconds. •Pressing this button while the alarm is sounding stops the alarm. 2Alarm Time Set buttons Use these buttons to change the alarm time or current time setting. 3SET button Use this button when setting the current time. 4WAVE button Press this button to receive the time calibration signal and adjust timekeeping. 5Alarm Mode selector SNZ: Snooze alarm on ON: Alarm on OFF: Alarm off 6RESET button Press this button to reset the clock after replacing its batteries. 7MAX/MIN TEMP. button Press this button to display the high and low temperature values. 8MAX/MIN HUMIDITY button Press this button to display the high and low humidity values. 9CLEAR button Press this button to clear the currently displayed high/low temperature or humidity. 0°C/ °F button Press this button to toggle the temperature units between Celsius and Fahrenheit. ARE-SYNC button Press this button to re-synchronize the timing of the main unit and the sub-unit. BSELECT button Press this button to toggle the display between main unit (INDOOR) and sub-unit (OUTDOOR) data. Sub-unit CSELECT button Press this button to toggle the display between the current temperature and humidity. DRESET button Press this button to reset the sub-unit after replacing its batteries. ETEST button This button is for testing the unit. Normally, you should not press it. If you do, be sure to press the RESET button (D) next. F°C/ °F button Press this button to toggle the temperature units between Celsius and Fahrenheit. Operation Guide DQR-300U 2 •A sticker is affixed to the glass of this clock when you purchase it. Be sure to remove the sticker before using the clock. • Depending on the clock model, the configuration of your clock may differ somewhat from that shown in the illustration. Alarm Off Alarm On •In locations subject to radio frequency interference, the product may malfunction and require you to reset the product. Alarm on indicatorPM indicator Wave OK indicator Antenna Icon Current Humidity Upcomimg weather indicator Current time (Hour, minutes, seconds) Day of the week DATE (month - date) Current Temperature Snooze on indicator Alarm time GENERAL GUIDE Main unit 1SNOOZE/LIGHT button •Press this button to illuminate the display for about four seconds. •Pressing this button while the alarm is sounding stops the alarm. 2Alarm Time Set buttons Use these buttons to change the alarm time or current time setting. 3SET button Use this button when setting the current time. 4WAVE button Press this button to receive the time calibration signal and adjust timekeeping. 5Alarm Mode selector SNZ: Snooze alarm on ON: Alarm on OFF: Alarm off 6RESET button Press this button to reset the clock after replacing its batteries. 7MAX/MIN TEMP. button Press this button to display the high and low temperature values. 8MAX/MIN HUMIDITY button Press this button to display the high and low humidity values. 9CLEAR button Press this button to clear the currently displayed high/low temperature or humidity. 0°C/ °F button Press this button to toggle the temperature units between Celsius and Fahrenheit. ARE-SYNC button Press this button to re-synchronize the timing of the main unit and the sub-unit. BSELECT button Press this button to toggle the display between main unit (INDOOR) and sub-unit (OUTDOOR) data. Sub-unit CSELECT button Press this button to toggle the display between the current temperature and humidity. DRESET button Press this button to reset the sub-unit after replacing its batteries. ETEST button This button is for testing the unit. Normally, you should not press it. If you do, be sure to press the RESET button (D) next. F°C/ °F button Press this button to toggle the temperature units between Celsius and Fahrenheit. Operation Guide DQR-300U 3 TIME CALIBRATION SIGNAL RECEPTION PRECAUTIONS •This clock is able to receive the time calibration signal transmitted from Rugby, England. Signal reception is possible within approximately 1,000 km of the transmitter. •Even when the clock is within the reception range, signal re...