Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
This module can be used as a simple clock display or it can display data from any BIM module attached to the system as well as several gauge values from the control box sensors. Most versions of this module come with at least one switch in the face to allow the display to change between various screens. Some versions may also contain two additional switches in the face which can be used as the SW1 and SW2 for the VHX control box with the use of the switch harness provided with it. CONNECTION: The auxiliary display has a connector on the rear that will accept a normal CAT 5, CAT 5E, or CAT 6 patch cable. This can be used to connect the module to any available port on the VHX control box (same locations the main VHX gauges plug into). ACC. POWER CONST. POWER GROUND TACH WARN SPD + SPD SND SPD - SPD OUT SW2 (-) SW1 (-) ADJ SND ADJ - WTR SND WTR - OIL + OIL SND OIL - FUEL + FUEL SND FUEL - WAIT (+) CRUISE (-) GEAR (1 WIRE) 4x4 (-) RIGHT (+) LEFT (+) HIGH (+) BRAKE (-) CHECK ENG (-) VHX CONTROL BOX CABLE AUX. I/O DISPLAY techsupport@dakotadigital.com 605-332-6513 DIM (+) ORANGE GREEN Used for displays with 3 switches Connection for all auxiliary displays Use any open jack Auxiliary Display module VHX control box OR SWITCH HARNESS: Some auxiliary modules will come with the pictured switch harness to allow additional switches in the clock face to function as switch 1 and 2 for the main VHX system. Auxiliary modules with 3 switches on front: Connect the orange wire to SW1(-) terminal on VHX control box. Right switch will be SW1 (speed display). Connect the green wire to SW2(-) terminal on VHX control box. Left switch will be SW2 (tach display). Leave blue wire unconnected. Center switch will be SW3 (clock display) Auxiliary modules with no switches on front: If the module has no switches, connect an external switch from the blue wire of the harness to ground to allow switch operations for the clock display. The orange and green wires would be left unconnected in this case. ORANGE (switch 1) GREEN (switch 2) BLUE (switch 3) SETUP: To enter setup, press and hold the switch (for systems with 3 switches, hold the center switch) while turning on the key. The display will read “SETUP”. Release the switch and the setup menu will be entered. Below is an outline of the setup options. Following the outline are more detailed instructions for each option. Press and release the switch to move through the various setup options or to change a setting. Press and hold the switch to select a setup option or to save a changed setting. SETUP CONTRAST Allows adjustment of LCD contrast. VERSION Displays software version UPDATE SPD Sets update speed of fast changing displayed data (such as tachometer) SLOW Slowest update speed of data MED Medium update speed FAST Fastest update speed TEMP UNIT Selects unit used for temperature displays F or C Fahrenheit or Celsius SCREENS Allows turning different display screens on or off SET DEFAULTS Sets all the settings back to factory default values DONE Leaves setup and returns to normal operation. CONTRAST: This option allows adjustment of the display contrast to best suit the particular mounting location in your vehicle. Enter setup. Press and release switch until “CONTRAST” is displayed, then press and hold switch “CONTRAST” will display with a contrast bar below it. Press and hold the switch to increase the contrast. Release the switch and press and hold again to reduce the contrast. Each time the switch is release the direction of contrast adjustment will change. Once contrast is set stop pressing the switch. After about 5 seconds without a switch press the contrast setting will be saved and setup will return to the main menu. VERSION: This option will display the version of the software in the display module. This information may be needed if you are calling for technical assistance. Enter setup. Press and release switch until “VERSION” is displayed, then press and hold switch. The software version will be displayed (example: VER VC01). Press and release switch to return to main menu. UPDATE SPD: This option sets the fastest update speed of screens. The effect will be most noticed when the tachometer screen is displayed. The fastest setting will allow frequent updates so the reading is more accurate at any given time. Fast changing readings may be difficult to read or distracting so some customers prefer to read a slower averaged reading which is available in the MED or SLOW setting. Default setting is MED. Enter setup. Press and release switch until “UPDATE SPD” is displayed, then press and hold switch. Press and release switch to toggle through speed settings. Press and hold switch when desired setting is displayed to save setting. “DONE” will be displayed. Release switch to return to main menu. 2 MAN #650360 TEMP UNIT: This setting determines which temperature unit is used when displaying temperatures. This unit setting will be independent of the units used in the main...