Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
Top “set” button advances hours, bottom “set” button advances minutes. Each time that you make a change to either the hours or minutes, the seconds are reset to zero. Adjusting the accuracy: The clock is accurate to +/-2 minutes a month as it is sent. It can be tuned for better accuracy if desired. Press and hold both of the set buttons for several seconds. The clock will display “C 0”. The “C” indicates that it is in the calibration mode and the second number is the current calibration value. The calibration value indicates the number of seconds to add or subtract each day. The clock can be adjusted from +7 sec/day to -7 sec/day. Press the minute set button to change the cal value. Press the hour set button to return to normal clock operation. Wiring: BLACK - connect to a good ground point in the vehicle. RED - connect to switched 12 volt power point. (An accessory terminal will work for this.) ORANGE - connect to a constant 12 volt power point. (This will keep the correct time.) BLUE - connect to the tail light circuit. Mounting: The gauge requires an oval cut out that as shown below. It should be inserted into the opening from the front and the U-clamp will be installed from the back. Tighten the two nuts on the U-clamp so that the gauge is secure. Figure 2 shows the required cut out for the gauge. Figure 3 shows how the gauge mounts. DASH CUTOUT Troubleshooting guide. Problem Possible cause Solution Clock will not light up Red wire does not have Connect to a location that has power power. when the key is on. Orange wire does not have Connect to a location that has power power. all of the time. Black wire is not getting Connect ground to a different location. a good ground. Power is reversed. Connect black to negative ground, red and orange to +12V power. Clock is damaged. Return clock for repair. (see instructions) Clock will not turn off when The red and orange wires Connect the red to switched power, the the key is off. are reversed. orange to constant power. Clock lights up, but does Loose connection on orange Reconnect orange wire. not read correctly. power wire. Poor ground connection. Move ground to different location Time is not set. Set time. (see instructions) Clock is damaged. Return clock for repair. (see instructions) Clock will not keep time. Orange wire does not have Connect to a location that has power when constant power. the key is on or off. Loose connection on orange Reconnect orange wire. power wire. Poor ground connection. Move ground to different location Clock will not dim. Blue wire is not connected Check wiring connections. correctly. Clock remains dim at all Blue wire is getting power Connect blue wire to location that only times. all of the time. has power when the headlights are on. Battery is very low. Recharge or replace vehicle battery. Clock is damaged. Return clock for repair. (contact factory) SERVICE AND REPAIR DAKOTA DIGITAL offers complete service and repair of its product line. In addition, technical consultation is available to help you work through any questions or problems you may be having installing one of our units. Should you ever need to send the unit back for repairs, please package the product in a good quality box along with plenty of packing material. Ship the product by UPS or insured Parcel Post. Be sure to include a complete description of the problem, your full name and address (street address preferred), and a telephone number where you can be reached during the day. An authorization number for products being returned for repair is not needed. Do not send any money. We will bill you for the repair charges. Any returns for warranty work must include a copy of the dated invoice or bill of sale. Technical specifications Minimum operating voltage - 7 volts Maximum operating voltage - 18 volts (operating at or near maximum rating for an extended time can damage unit) Clock accuracy - ±2 minute per month Typical current draw (@ 13.8V) - 0.13 A Standby current draw (key off) - 0.002 A ODYSSEY SERIES DIGITAL GAUGE LIMITED WARRANTY DAKOTA DIGITAL (the Company) warrants to the ORIGINAL PURCHASER of this product that should it, under normal use and condition, be proven defective in material or workmanship within 24 MONTHS FROM THE DATE OF PURCHASE, such defect(s) will be repaired or replaced (at the Company’s option) without charge for parts or labor directly related to repairs of the defect(s). To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g. dated bill of sale), name, address, phone number, and specification of defects, transportation prepaid, to the factory. This Warranty is valid for the original purchaser only and may not be transferred. This warranty does not cover nor extend to damage to vehicle electrical system. This Warranty does not apply to any product or part thereof which in the opinion of the Company has been damaged through alteration, improper installation, ...