232915 232918 Related Manuals Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 309066 Displacement Pump . . . . . . . . . . . . . . . . . 308815 Fluid Filter . . . . . . . . . . . . . . . . . . . . . . . . . . 308249 Spray Gun . . . . . . . . . . . . . . . . . . . . . . . . . 309091 Spray Tip . . . . . . . . . . . . . . . . . . . . . . . . . . . 309055 232917 232916 232919 232914 9659A 9660A 232665 INSTRUCTIONS-PARTS LIST INSTRUCTIONS This manual contains important warnings and info

Flammable materials spilled on the hot, bare motor could cause a fire or explosion. . . Motor Test WARNING INJECTION HAZARD To reduce the risk of serious injury, when instructed to relieve pressure, follow the Pressure Relief Procedure on page 8. For checking armature, motor winding and brush electrical continuity. Setup 1. Unplug sprayer. 2. Remove drive housing. See page 26. This is to ensure that any resistance you notice in armature test is due to motor and not to worn gears in drive housing

See Fig. 4. 3. Check to see that the air motor piston is at the top of the stroke. If it is not, first read the warning above. Then, while keeping your fingers away from moving parts, apply very low pressure air to the air inlet to move the piston up. Close the air regulator and disconnect the air supply hose. Refer to Fig. 3. 4. Use a 1/4” diameter rod, spanner wrench, or torque wrench to tighten the packing nut. First loosen the nut, then tighten snugly, and finally tighten an additional 1/2 t

A pump which runs too fast can be seriously damaged. . An air line lubricator (G) provides automatic air motor lubrication. . A bleed-type master air valve (F) relieves air trapped between it and the motor when the valve is closed. Order Part No. 107142. . The air regulator (E) controls pump speed and pressure. . An air line filter (D) removes harmful dirt and contaminants from your compressed air supply. . A drain valve (L) is required near the pump fluid outlet to relieve fluid pressure in the

1. Turn the pressure adjusting knob (A) fully counterclockwise to minimum pressure. 2. Put the intake tube (3) in the fluid container. 3. Plug in the sprayer. CAUTION Do not run the pump without fluid in it for more than 30 seconds to avoid damage to the displacement pump packings. WARNING FIRE AND EXPLOSION HAZARD To reduce the risk of static sparking and splashing when flushing, always remove the spray tip from the gun and hold a metal part of the gun firmly to the side of grounded metal pail.

Related Manuals 311777 311768 US C Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441 Conforms to ANSI/UL Copyright 2006, Graco Inc. is registered to I.S. EN ISO 9001 standard 1450 Warnings Warnings The following are general warnings related to the setup, use, grounding, maintenance and repair of this equipment. Additional, more specific warnings may be found throughout the body of this manual where applicable. Symbols appearing in the body of the manual refer to these general warnings. When th

Then, insert the Pump Handle back into the Container and turn the Pump Handle clockwise to secure it in place. (See Figure A.) PUMP HANDLE (43) SAFETY RELEASE VALVE (20) CONTAINER CAPACITY: MODEL 95690 = 2 GALLONS MODEL 95692 = 1.25 GALLONS (DO NOT OVERFILL) CONTAINER (31) FIGURE A 5. NOTE: The Sprayer is heavy when completely filled with liquid. Always get assistance when strapping the Sprayer onto your body. If necessary, adjust the Belt (28) for comfort. (See Assy. Diagram.) 6. Always make su

Save this manual. Copyright© 2007 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included. For technical questions or replacemen

READ AND KEEP FOR REFERENCE. HydraMax Sprayers HydraMax 225 3600 psi (248 bar, 24.8 MPa) Maximum Working Pressure) Model Series Direct Immersion 30 Gallon Suction RAC X, Silver Gun and Hose 233640 B X 233641 B X 233642 B X X 233643 B X X HydraMax 300 3600 psi (248 bar, 24.8 MPa) Maximum Working Pressure) Model Series Direct Immersion 30 Gallon Suction RAC X, Silver Gun and Hose 233650 B X 233651 B X X HydraMax 350 4000 psi (276 bar, 27.6 MPa) Maximum Working Pressure) Model Series Direct Immersi

An in-line shutoff ball valve is an important safety device because it controls the air supply even if the air hose is ruptured. The shutoff valve should be a ball valve because it can be closed quickly. Note: Do not use an automatic oiler system or add oil to airline. The oil will contaminate the material being propelled, ruining the final result. 2. Attach an air hose to the compressor’s air outlet. Connect the air hose to the air inlet of the tool. Other components, such as a coupler plug and