WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. PRINTED IN CHINA H5528 & H5529 Parts Diagram REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PH5528001 BREATHER PLUG 2 PH5528002 RESERVOIR COVER 3 PH5528003 PLASTIC RESERVOIR 4 PH5529004 ALUMINUM RESERVOIR 5 PH5528005 FILTER 6 PH5528006 FLUID INLET JOINT SEAL 7 PH5528007 FLUID INLET JOINT 8 PH5528008 HANGER 9 PH5528009 FLUID ADJ. NEEDLE 10 PH5528010 FLUI

Spray gun controls. ADJUSTMENTS Identify the spray gun controls in Figure 1 and adjust in the following order: 1. Fluid Control—Adjusts how far back the trigger can be pulled, which affects the volume of finish released. 2. Air Flow Control—Adjusts the volume of air that mixes with the finish, and thus, increases or decreases the finish atomization. 3. Pattern Control—Variably adjusts the spray pattern from round to a wide fan. 4. Nozzle Control—Adjusts the spray pattern from vertical to

Always thoroughly clean the spray gun after each use. to clean the spray gun: 1. spray a small amount of cleaning solvent through the gun. note: Check with local laws regarding this practice. If you are spraying on a regular basis, spraying solvents into the air may be illegal. A cabinet style spray gun cleaner may be required. 2. disConneCt sprAy gun FroM Air! 3. remove the cup and cup lid, then disassemble the gun by unscrewing the fluid control knob and removing the spring and needle (see fig

Overloading can cause the jack to collapse and drop the load. 2. ALWAYS support the vehicle with appropriately rated support stands before working under it. 3. DO NOT attempt to move the vehicle while the jack is in use. 4. Use only on hard level surfaces like concrete or asphalt. Other surfaces are potentially unstable. 5. Center the load on the jack to maintain proper balance and stability. 6. DO NOT use jack if it begins leaking fluid or if it slowly sinks with a heavy load. These are in

start with the tank at "zero" pressure and increase pressure gradually until the correct spray pattern is achieved. respiratory hazard! always use a niosh approved respirator when using spray equipment. failure to protect your lungs can lead to respiratory illness and nervous system damage. spraying some paints and varnishes may require a supplied air respirator system. Model h6329 21.2 gallon paint tank -7 -8- Model H6329 21.2 Gallon Paint Tank Read the manual before operation. Become familiar

• Secure the unit carefully to prevent movement when it is transported. • A unit that receives a strong shock during transport and unloading may malfunction. STORAGE • Clean and rinse tank and spraying assembly after each use to prevent crystallizing, which would later cause clogging and chemical damage to the unit. • Do not store sprayer under pressure, or with spray solution in tank. • When storing the sprayer, choose a space indoors free from moisture and out of the reach of children. 4. Afte

shutting off air valves. 3. Keep WorK area clean. 7. do not force tool. it will do Cluttered areas and benches invite the job better and safer at the rate accidents. for which it was designed. 4. do not use in dangerous 8. use the right tool. do not environment. do not use pneu-force tool or attachment to do a job matic tools in damp or wet loca-for which it was not designed. tions, or where any flammable or 9. do not use under the noxious fumes may exist. Keep influence of drugs or work area we

150 PSI maximum air pressure. 1.4" NPT. Figure 6. G6261 Campbell Hausfeld™ water filter. G8114—3.8" x 25 Ft. Air Hose G8115—3.8" x 50 Ft. Air Hose G8116—3.8" x 100 Ft. Air Hose Multi-purpose red rubber air hose is flexible and abrasion resistant. Rated for 200 PSI, this air hose has a bursting strength of 800 PSI and 1.4" NPT ends. Figure 7. Red rubber air hose. H7274—Campbell Hausfeld™ Pressure Regulator Provides regulated output pressure of 0 to 125 PSI for proper tool operation. Locking press