Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
Notice indicates NOTICE important information that, if not followed, may cause damage to the equipment. IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS – To reduce the risk of fire or explosion, electrical shock and injury to persons, read and understand all instructions included in this manual. Be familiar with the controls and the proper usage of the equipment. ! DANGER ELECTRICAL SHOCK HAZARD: To prevent electrical shock, observe the following guidelines at all times: GROUNDING INSTRUCTIONS This product must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This product is equipped with a cord having a grounding wire with an appropriate grounding plug. The plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances, as well as the National Electrical Code (NEC) and, in the United States, the Occupational Safety and Health Act (OSHA). Improper installa ! WARNING tion of the grounding plug is liable to result in a risk of electric shock. When repair or replacement of the cord or plug is required, do not connect the grounding wire to either flat blade terminal. The wire with insulation having an outer surface that is green,with or without yellow stripes, is the grounding wire. Check with a qualified electrician or serviceman when the grounding instructions are not completely understood, or when in doubt as to whether the product is properly grounded. Do not modify the plug provided; if it does not fit the outlet, have the proper outlet installed by a qualified electrician. This product is for use on a nominal 120-V circuit and has a grounding plug similar to the plug illustrated in Figure 1. Only connect the product to an outlet having the same configuration as the plug. Do not use an adapter with this product. TEST RESET Figure 1 - Grounded three-wire extension cord Table 1 – Extension Cords for 120V/15 Amp Unit Length of Cord (ft.) 25-50 50<100 100<150 150<250 250<400 400-500 Gauge of Cord 18 16 14 12 10 2 General Safety (Cont.) Extension Cords: Use only a 3-wire extension cord that has a 3-blade grounding plug, and a 3-slot receptacle that accepts the plug on the product. Make sure the extension cord is not damaged. When using an extension cord, be sure to use one heavy enough to carry the current the product draws. An undersized cord results in a drop in line voltage and loss of power and overheating. See Table 1 on Page 2. Do not modify any of the electrical components of this equipment. To reduce the ! WARNING risk of fire or explosion: • Do not spray flammable or combustible materials near an open flame or sources of ignition such as cigarettes, motors and electrical equipment. • Paint or solvent flowing through the equipment is liable to result in static electricity. Static electricity creates a risk of fire or explosion in the presence of paint or solvent fumes. All parts of the spray system, including the pump, hose assembly, spray gun and objects in and around the spray area should be properly grounded to protect against static discharge and sparks. Use only conductive or grounded high-pressure airless paint sprayer hoses specified by the manufacturer. • Verify that all containers and collection systems are grounded to prevent static discharge. EZ5000 Series • Connect to a grounded outlet and use grounded extension cords. Do not use a 3 to 2 adapter. • Do not use a paint or a solvent containing halogenated hydrocarbons as this attacks the aluminum and increases the risk of bursting. Examples of improper solvents are methyl bromine, carbon tetrachloride and ethyl iodide. • Keep spray area well-ventilated. Keep a good supply of fresh air moving through the area. Keep pump assembly in a well-ventilated area. Do not spray pump assembly. • Do not smoke in the spray area. • Do not operate light switches, engines, or similar spark-producing products in the spray area. • Keep area clean and free of paint or solvent containers, rags and other flammable materials. • Know the contents of the paints and solvents being sprayed. Read all Material Safety Data Sheets (MSDS) and container labels provided with the paints and solvents. Follow the paint and solvent manufacturer’s safety instructions. • Fire extinguisher equipment shall be present and working. • Due to flammability, use caution when using solvents with flash points less than 70F (21C) to clean equipment. Examples of acceptable cleaning solvents include water, mineral spirits and lacquer thinner. Unacceptable cleaning solvents include naphtha, MEK, acetone, alcohol and toluene. 3 4 Operating Instructions & Parts Manual General Safety (Cont.) To reduce the risk of skin injection: • Do not aim the gun at or spray any person or animal. • Keep hands and other body parts away from the discharge. Do not try to stop leaks with any part...
Dieses Handbuch ist für folgende Modelle:Farbspritzpistolen - HousePainter EZ5000 (1.44 mb)
Farbspritzpistolen - HousePainter IN423200AV (1.44 mb)