Stimmen - 3, Durchschnittliche Bewertung: 3.3 ( )

Hersteller: Campbell Hausfeld Dateigröße: 7.95 mb Dateiname: 4659121e-dead-4673-8744-310b7f22a50c.pdf Unterrichtssprache:

Before performing any maintenance, make sure to relieve pressure from system and disconnect power from sprayer. • Do not use oil based solvents to clean equipment after using latex based coatings. Use only warm soapy water. • Always replace clogged gun filters, do not attempt to clean them. • Carefully follow cleaning and storage instructions for your sprayer. • Do not use metal or other hard objects to pick dried paint material from Spray Tip Orifice. TrIGGEr lOCk pulling the trigger must not open the gun valve when trigger lock is activated. You should be able to get the actuator (#12, page 19) to wiggle slightly with your finger while holding the trigger against the trigger lock when it is in the locked position. If you cannot, adjust the trigger position by following these instructions: 1. Place trigger in locked orientation (tabs horizontal). 2. With one hand holding trigger lightly against lock, use a 1/4 inch nut driver to turn nut (#13, page 19) in until trigger starts to come off the lock. 3. Reverse the nut (counterclockwise) 1/2 turn. TIP SEAl AND wAShEr Occasionally, you will need to replace the silver seal and clear washer located inside the tip base. 1. To replace seal and washer, first loosen tip base with adjustable wrench, and then remove by hand. 2. Remove spray tip. 3. With Phillips screwdriver, push seal and washer out from front of tip base. 4. With flat side of seal facing up, place seal in base. Make sure it lines up properly with base. 5. Place washer in base. Make sure it lines up properly with base. 6. Put spray tip back in tip base. 7. Reattach tip base to gun valve. Makesurespraytipandtipbasefitsnuglyinplace.Aloosefitcanleadtomisdirectedspraydischargeandaskininjectionhazard. 1 115 55 Operating Instructions and Assembly Instructions Airless Paint Sprayers maintenance Chart maintenance User Item Check replace Serviceable? Detail Notes Product safety Before each use As required Yes See parts listing for location of product safety labels labels and related part numbers. Trigger adjustment Before each use Yes See trigger lock warning under Spray Gun Maintenance. Airless hose Before each use Yes Read information on the hang tag attached to the high pressure hose for instructions on maintenance. Sealing surfaces Before each use Yes Make sure they are clean. Suction tube Before each use As required Yes Check for nicks and cuts. Bypass tube Before each use As required Yes Check for nicks and cuts. Suction filter Before each use Every 25 gal. or Yes and every 5 gal. more often if required Gun filter Before each use Every 25 gal. Yes Do not attempt to clean gun filter, only replace. Roller nap Before each use As required Yes Prime/spray valve Before each use Every 1000 gal. Yes 3/4” Wrench, torque to 80 in/lbs. Push button Before each use Every 1000 gal. Yes 7/8” Socket or wrench, torque to 200 in/lbs. Block bolts Before each use Do not require Yes Block bolts are to be torqued to 275 in/lbs. in an replacement “X” pattern. These bolts should be checked periwith normal use odically for correct torque. 1/4” Hex. Pressure valve Does not require *SCR 5/8” Wrench, torque to 75 in/lbs. replacement with normal use Inlet valve Every 250 gal. Yes 1-1/16” Wrench, torque to 150 in/lbs. Outlet valve Every 250 gal. Yes 3/4” Wrench torque to 150 in./lbs. Spray tip Before each use Every 20-75 gal. Yes 1” Wrench torque to 135 in/lbs. Diaphragm Every 1000 gal. *SCR This part is only worn out if broken or torn. assembly Oil Every 2000 gal. Yes H-32 Hydraulic oil CH #AL170200AV. Block Does not require Yes replacement with normal use Hose connector Before each use When stripped or leaking under Yes 5/8” -Torque to 350 in/lbs. pressure * Service Center Recommended 16 Operating Instructions and Assembly Instructions Airless Paint Sprayers Specifications Operating Pressure model A D Power ratings model E & F Power ratings Safety Features 0-3000 psi 115 Volts AC 220 -240 Volts AC Spray gun trigger lock 60 Hz 50 Hz Spray gun trigger guard 8.5 Amps 4.6 Amps Spray gun pressure diffuser Prime/Spray valve over pressure relief model weight (lbs.) Capacity (GPm) maximum hose length maximum Tip Size @ 0 psi @ 2000 psi PS2###B/E 49 * .42 .26 100 ft. .015 in. PS2###C/F 55 * .50 .31 150 ft. .017 in. PS2###D 55 * .60 .43 200 ft. .019 in. * Weight does not include mounting PS###B MC014500SV AL133509SV AL125905SV AL116200SV AL131401SV PS###C MC014502SV AL133509SV AL125906SV AL116201SV AL131401SV PS###D MC014503SV AL173304SV AL173700SV AL116204SV AL131403SV PS###E MC014520SV AL133509SV AL125905SV AL116200SV AL131401SV PS###F MC014521SV AL133509SV AL125906SV AL116201SV AL131401SV NOTE: All check valve components come with the diaphragm kits. model motor kit housing kit Diaphragm kit Eccentric / bearing Pressure valve kit 1 Replacement Parts List 18 For Replacement P arts and Accessories, Contact Your L ocal Service C enter or C all 1-800-626-4401 Operating Instructions and Assembly ...

Herunterladen

Geben Sie zwei Ziffern: