Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
MASK ANY AREA YOU DO NOT WISH TO SPRAY. Once you have set up ready to spray, switch on the unit. No paint will be sprayed from the gun until the trigger on the spray gun is pulled. Before starting any work on spraying actual objects we suggest you spend a small amount of time practicing on cardboard or newspaper until you have got used to how the gun works. 11 SPRAY PATTERNS Fig.2 Vertical Jet Round JetHorizontal Jet The gun has 3 different spray patterns – Horizontal, Vertical and Round (Fig.2) The horizontal and vertical are recommended for large surfaces. The round spray is used for small objects or for areas - such as corners – that are difficult to reach. To adjust the spray pattern, loosen the adjustment ring (9), adjust the position of the air cap (8) to obtain either a vertical, horizontal or round pattern then re-tighten the adjustment ring. 12 PAINT VOLUME The volume of paint sprayed is easily adjustable. (Fig.3) Fig.3 Completely close adjustment screw (4) by turning this clockwise as far as it will go. Whilst pulling the trigger, begin turning the adjustment screw anti-clockwise until the volume of paint you require is obtained. If the paint spray is too wide or contains too much paint turn the adjustment screw clockwise again. Once the correct spray pattern is obtained you are able to commence spraying. 13 SPRAYING TECHNIQUE 1. To obtain the best results always keep your spray gun level and spray equally from side to side or up or down 25-30cm (10”-12”) from the surface. Avoid spraying at an angle as this will lead to runs on the surface (Fig.4). 2. Let your arm control the left to right movement rather than your wrist as this will aid even paint distribution over the whole area (Fig.4). 3. Do not tip the sprayer to more than 45o angle. 14 Fig.4 Fig.4 15 HELPFUL HINTS 1. Evenly control the speed of movement of the spray gun. A fast speed will give a thin coat and a slow speed will give a heavy coat. 2. Only apply one coat at a time. If a further coat is required follow the paint manufacturer’s instructions for drying times. 3. If spraying small areas or objects keep the output setting low as this will avoid excessive use of paints and will minimise overspray. 4. When spraying large areas or objects, it is best to use a criss-cross pattern, either from left to right then up or down or vice-versa. This will ensure maximum coverage (Fig. 5). 5. Avoid stopping and starting when spraying as this can lead to too much or not enough material on a surface. 6. To ensure edges are covered, commence spraying just to the side of area being sprayed 7. CLEAN SPRAYER AFTER EVERY USE (SEE CLEANING INSTRUCTIONS) 16 Fig.5 Fig.5 17 CLEANING INSTRUCTIONS THE SPRAY GUN MUST BE THOROUGHLY CLEANED IMMEDIATELY AFTER USE. IF THE PAINT DRIES INSIDE THE GUN, CLEANING WILL BECOME MUCH MORE DIFFICULT AND MAY RENDER THE GUN INOPERABLE. THIS IS NOT COVERED BY GUARANTEE. The spray gun is the same as a paintbrush, if it is not cleaned it will go hard and can become useless. You must therefore clean this out after use. GUN . Disassemble the gun container . Pour any residual material into its container so that it can be used for the future. . Pour a quantity of the respective thinner into container, shake the gun lightly, reassemble the gun, then spray this liquid through the gun. Repeat this until the thinner being sprayed is coming through with no traces of paint. . Clean any traces of paint off the outside of the gun . Clean the gasket (11) inside the gun body 18 NOZZLE & NEEDLE . Unscrew Adjustment Ring (9) . Remove the Air Cap (8) . Completely remove Adjustment Screw (4) . Remove the Spring (3) . Push out the Needle (2) – do not use tools for this . Remove the Fluid Tip (7) . Remove Air Flow Plate (6) . Remove Nozzle Washer (17) . Place all of these items into a container and clean them using a brush and clean thinners . Clean the inside of the gun . Thoroughly dry these parts before reassembling . Grease the Fluid Needle Packing (13) . Reassemble parts in reverse order. It is recommended fitting the fluid tip (7) prior to the needle NEVER DISPOSE OF PAINTS OR SOLVENTS INTO DRAINS. CONTACT YOUR LOCAL COUNCIL TO ARRANGE COLLECTION OR FOR DETAILS OF NEAREST REGISTERED DISPOSAL SITE. 19 TURBINE UNIT The turbine unit only requires minimal maintenance . Ensure its filter element is kept clean at all times. This is the filter underneath the main body (19). Disconnect the unit from the mains, turn on side and remove foam material. This can be washed out if necessary and replace when dry. From time to time this filter will need replacing (part no.L0058). . The turbine bearings are sealed and lubricated for life. There is no maintenance or adjustment required. . Clean the turbine and hose unit with a damp cloth after use. . The hose is stored by locating this into the clips on the side of the main body . The mains lead is stored by wrapping around the base of the unit and locating the plug in the space at the back of the unit. . The c...