Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
BEFORE USE – PLEASE READ THE MANUAL AND SAFETY INSTRUCTIONS. Please retain for future reference MODE D’EMPLOI Merci d’avoir choisi le systeme professionnel de pulverisation de peinture basse pression Earlex. Cet appareil est dote du systeme HVLP (haut volume d’air, basse pression de peinture) extremement polyvalent dont vous pourrez vous servir pour une grande variete d’applications. AVANTTOUTE UTILISATION,VEUILLEZ LIRE CE MANUEL ET LES INSTRUCTIONS RELATIVES A LA SECURITE. Veuillez conserver ce document afin de le consulter ulterieurement MANUAL DE INSTRUCCIONES Gracias por comprar esta unidad profesional de pintura a baja presion Earlex. Este versatil aparato HVLP (equipo de pintura de gran caudal de aire y baja presion) se puede utilizar para una gran variedad de aplicaciones. LEA LAS INSTRUCCIONES DE SEGURIDAD Y FUNCIONAMIENTO ANTES DE UTILIZAR EL APARATO. Guarde estas instrucciones para futuras consultas. SAFETY OPERATING INSTRUCTIONS PLEASE READ BEFORE USE USPLEASE READ BEFORE USE US . The substances used with this spray applicator (paint, thinners etc) may contain hazardous, harmful, explosive or corrosive materials. . The spray applicator must only be used with paints and solvents that have a suitable flash pointfor spraying. If in doubt, consult the paint or solvent manufacturer's data . Always ensure there is adequate ventilation when spraying. . NEVER spray near an open flame, including an appliance pilot flame. . NEVER smoke when spraying. . Always disconnect the unit from the mains supply cleaning the spray applicator. . Always ensure the spray area is safe and free from all debris that may present a fire or trip hazard. . NEVER, under any circumstances, point the spray gun at another person or animal. In theevent of injury occurring, seek expert medical advice immediately. . NEVER allow children or unauthorised users to operate or play with the spray equipment. This equipment is for professional use only. . Always read the paint manufacturer's thinning instructions before use. . Always wear the correct protective face mask when spraying. We also recommend wearinggloves, goggles and overalls. . After every use ensure that you clean the spray gun thoroughly and grease the gland washer. . Use only genuine manufacturer replacement parts. . Only use the spray equipment as detailed in these instructions. . Do not use the air hose or mains cable to pull the HVLP unit. . Check the hoses, hose connectors and mains cable daily. Any worn or damaged parts shouldbe replaced immediately. . This appliance is recommended for household use only. . This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have beengiven supervision or instruction concerning use of the appliance by a person responsiblefor their safety. WARNING: The substances used with this Spray Gun (paints, solvents, etc.) may containdangerous, harmful, explosive or corrosive materials. ALWAYS COMPLY WITH THESAFETY INSTRUCTIONS ISSUED WITH THIS PRODUCT AND THE MATERIAL BEING USED. Only use the Spray Station as described in this manual. TECHNICAL SPECIFICATION: Wattage: 1100 Watts Container capacity: 1 litres Voltage: 120 V (60hz) Air hose length: 4.5 m Air output: 22L/sec Dynamic air pressure: 0.30 bar Sound pressure level: 88 dB (A) Maximum viscosity: 250DIN/sec PARTS LIST Fig.1 No Description 1. Air Cap Ring 2. Air Cap 3. Air Distributor Plate 4. 0.08” (2.0mm) Fluid Tip 5. Fluid Tip Seal 6. Pivot Screw 7. Washer 8. Main Body Assy 9. 0.08” (2.0mm) Fluid Needle 10. Adaptor 11. Needle Spring 12. Fluid Adjusting Screw 13. Pivot Part No L0151 L0517 L0162 L0157 L0159 L0179 L0195 L0180 L0166 L0174 L0175 L0176 L0178 No Description Part No 14. Flexible Tube Air Feed L0182 15. Gland Nut L0173 16. Gland Seal (2 pcs) L0168 17. Trigger L0177 18. Centre Bolt & Pick Up Tube Assy L0183 19. Yoke L0184 20. Clamp Lever L0185 21. Shim L0186 22. Lid Assy L0187 23. Gasket L0188 24. Centre Bolt Nut L0189 25. Paint Container L0190 26. Filter (x2) N0087 27. Air Hose N0212 Optional Accessory to Purchase 30. Hose -N0099 2 Mains Switch (120V) Power IN (IEC Connector) Circuit Breaker 1 2 3 4 5 6 7 8 9 10 11 12 7 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 (x2) EXPLODED PARTS VIEW DIAGRAMS Fig. 2 Vertical Spray Horizontal Spray Round Spray Fig. 3 Fig. 4 Let go of the trigger at the end of each spray movement to avoid excessive paint and drips. Fig. 1 US 3 INTRODUCTION UUSS The concept A motor feeds out a high volume of air (HV) and enables products to be sprayed at a low pressure(LP). The product is released from the Fluid Tip of the Spray Gun at a very low pressure (0.18 bar) and is enclosed in a high volume of air. The Hose feeds the air produced by the motor to the Spray Gun. The powerful motor can spray a width range of paint with or without dilution. However, there willalways be some paint which will not be suitable for the Spray Gun. The good qualit...