Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
Do not use latex paints with this Spray Gun. 2. Carefully strain the paint/material through a paint strainer or piece of cheese cloth. 3. Swing the Cup Locking Lever (39) out of the locked position to remove the Cup (43) from the Unit. Fill the Cup (43) to approximately 3/4 full. Place the Cup (43) back on the unit and swing the Cup Locking Lever (39) to the locked position. 4. Start the air compressor. 5. To adjust the spray pattern, set up a piece of scrap material to practice on. While practicing on the scrap material, check to see that the material you are spraying has the appropriate consistency. If it appears to thin, add a very small amount of thinner (not included). BE CAREFUL when thinning. Proceed slowly, adding very minimal amounts. NEVER exceed the manufacturer’s thinning recommendations. For technical questions, please call 1-800-444-3353; SKU 43760 Page 7 Troubleshooting section at end of manual. IMPORTANT: The Spray Gun must be cleaned immediately after use. Improper cleaning is a common reason for the Spray Gun not to work. Fan Direction and Pattern Adjustment Note: Always make sure the Vent (45) is clear and unclogged. Fan Direction To change the direction of the fan from horizontal to vertical, loosen the Lock Ring and turn the Air Cap (1) 90 degrees. After the adjustment, tighten the Lock Ring by hand. See FIGURE 3 below. FIGURE 3 Horizontal Fan Vertical Fan Air Cap Lock Ring Pattern Adjustment Warning!! Never exceed the Maximum Inlet PSI of 55 PSI. 1. If you need to reduce the air pressure for specific areas, adjust the air compressor. 2. To set the pattern size specific to the job, use the Pattern Control Knob (14) (see FIGURE 1 on page 6). By turning it counterclockwise (all the way open), the pattern will flatten. Turn the Pattern Control Knob (14) clockwise for a round pattern. See FIGURE 4 below. Flat/Open Round/Closed FIGURE 4 For technical questions, please call 1-800-444-3353; SKU 43760 Page 8 Troubleshooting section at end of manual. IMPORTANT: The Spray Gun must be cleaned immediately after use. Improper cleaning is a common reason for the Spray Gun not to work. Fan Direction and Pattern Adjustment (continued) 3. Turn the Fluid Control Knob (15) clockwise until it is fully closed. See FIGURE 1 on page 6. 4. After setting up a piece of scrap material, squeeze the Trigger (32) in short bursts while turning the Fluid Control Knob (15) counterclockwise and observe the spray patterns until you see the pattern you want. Also, look at the pattern for consistency. Too much air may cause the spray to come out too fine. Reduce the air pressure or allow more material to come out by opening the Fluid Control Knob (15). If the spray appears too thick (you see globs of paint), close down the Fluid Control Knob (15) slowly, checking the mixture after each adjustment. See FIGURE 5 below. FIGURE 5 Too Fine (Loosen) Too Coarse (Tighten) Correct For technical questions, please call 1-800-444-3353; SKU 43760 Page 9 Troubleshooting section at end of manual. IMPORTANT: The Spray Gun must be cleaned immediately after use. Improper cleaning is a common reason for the Spray Gun not to work. Techniques Note: Before spraying, mask all objects you do not want sprayed and lay cloths (not included) on the floors. 1. Always keep the gun at right angles to the workpiece (See FIGURE 6). Pull the Trigger (32) slowly and move the Spray Gun in parallel strokes to the object being painted. Keep the distance from the object being painted at 6” to 9”. This may slightly differ depending on the flow adjustment and the material being sprayed. Do not stop the gun movement while spraying. If you stop the gun for even just a slight pause while spraying, the paint will build up and run down the workpiece. FIGURE 6 (Heavier coat on one side, uneven coverage) Incorrect (Even coverage) Correct (90o) 2. To ensure you don’t allow paint to build up, start moving the Spray Gun before you Squeeze the Trigger (32). When you are finished spraying, release the Trigger (32) before you stop moving the Spray Gun. Doing so will eliminate distinct overlaps, producing a blended (feathered) affect. See FIGURE 7 below. EndBegin ReleaseSqueeze Stroke Trigger (32) FIGURE 7 Trigger (32) Stroke (Top View) Note: The speed of the stroke, the adjustment of the Fluid Control Knob (15), and the distance from the workpiece, will determine how much paint is being applied. To get the best results, try to apply two thin coats of paint versus one thick coat. 3. Clean out the gun thoroughly after EVERY use, according to the instructions found on the next page. For technical questions, please call 1-800-444-3353; SKU 43760 Page 10 Troubleshooting section at end of manual. IMPORTANT: The Spray Gun must be cleaned IMMEDIATELY after use. Improper cleaning is a common reason for the Spray Gun not to work properly. Materials dry quickly which will render the gun useless. It is extremely difficult to remove dry paint from small passages within the Gun. Maintenanc...
Dieses Handbuch ist für folgende Modelle:Farbspritzpistolen - 43760 (263.9 kb)