Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
This installation manual describes only the steps needed to register and begin using the handset. For further details, please read the base unit’s User Guide on the Panasonic Web site at: Charge the batteries for about 6 hours before initial use. Please read this installation manual before using the unit and save it for future reference. Printed in Malaysia PNQX2117XA DM0709SY3060 Accessory information Accessory information Accessory item/Order number Quantity Charger/PNWETGP500B 1 AC adaptor/PQLV219Z or PQLV219 (03)Z 1 Rechargeable batteries/HHR-4DPA (Part No. HHR-65AAABU or N4DHYYY00002) 2 Handset cover*1/PNYNTGA641TR 1 Belt clip/PNKE1029Z1 1 *1 The handset cover comes attached to the handset. Note: LPlease read the additional/replacement accessory section of the base unit’s User Guide on the Panasonic Web site. See page 1 for Panasonic URL. Setting up Connections (120 V AC, 60 Hz) Hooks Note: LUse only the supplied Panasonic AC adaptor PQLV219 or PQLV219 (03). LThe AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.) LThe AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.) LUse the supplied rechargeable batteries. For replacement, we recommend using the Panasonic rechargeable batteries noted on page 2. LWipe the battery ends (S, T) with a dry cloth. LAvoid touching the battery ends (S, T) or the unit contacts. LConfirm correct polarities (S, T). LUSE ONLY Ni-MH batteries AAA (R03) size. LDo NOT use Alkaline/Manganese/Ni-Cd batteries. Charge for about 6 hours. LWhen the batteries are fully charged, the charge indicator goes off. Charge indicator Rechargeable Ni-MH ONLY Confirm “Charging” is displayed. Note: LIf the batteries are fully charged, but the operating time seems to be shorter, clean the battery ends (S, T) and the charge contacts with a dry cloth and charge again. Registering a handset to the base unit 1 Base unit: NKX-TGP500 series Press and hold {ALL} for about 4 seconds until the STATUS indicator flashes in red. Registering a handset to the base unit 1 Base unit: NKX-TGP500 series Press and hold {ALL} for about 4 seconds until the STATUS indicator flashes in red. LIf all registered handsets start ringing, press the same button to stop. Then repeat this step. LThe next step must be completed within 90 seconds. 2 Handset: Press {OKL}, then wait until a long beep sounds. Note: LIf an error tone sounds, or if _ is still displayed, register the handset according to the registering section of the base unit’s User Guide on the Panasonic Web site. See page 1 for Panasonic URL. Display language 1 {MENU} (center of joystick) i {#}{1}{1}{0} 2 {V}/{^}: Select the desired setting. 3 Press down the center of the joystick to save. i {OFF} Belt clip NTo attach NTo remove Belt clip NTo attach NTo remove Wall mounting 1 Drive the screws (not supplied) into the wall. 2 Mount the charger (A), then slide it down (B) and to the right (C) until it is secure. 25.4 mm (1 inch) Screws ABC For your safety For your safety WARNING Power connection L Completely insert the AC adaptor/power plug into the power outlet. Failure to do so may cause electric shock and/or excessive heat resulting in a fire. L Regularly remove any dust, etc. from the AC adaptor/power plug by pulling it from the power outlet, then wiping with a dry cloth. Accumulated dust may cause an insulation defect from moisture, etc. resulting in a fire. L Unplug the product from power outlets if it emits smoke, an abnormal smell, or makes an unusual noise. These conditions can cause fire or electric shock. Confirm that smoke has stopped emitting and contact your phone system dealer. Installation L To prevent the risk of fire or electrical shock, do not expose the product to rain or any type of moisture. L Do not place or use this product near automatically controlled devices such as automatic doors and fire alarms. Radio waves emitted from this product may cause such devices to malfunction resulting in an accident. CAUTION Installation and relocation L The AC adaptor is used as the main disconnect device. Ensure that the AC outlet is installed near the product and is easily accessible. Battery L We recommend using the supplied batteries or additional/replacement batteries noted on page 2 for replacement battery information. USE ONLY rechargeable Ni-MH batteries AAA (R03) size. L Do not mix old and new batteries. L Do not open or mutilate the batteries. Released electrolyte from the batteries is corrosive and may cause burns or injury to the eyes or skin. The electrolyte is toxic and may be harmful if swallowed. L Exercise care when handling the batteries. Do not allow conductive materials such as rings, bracelets, or keys to touch the batteries, otherwise a short circuit may cause the batteries and/or the conductive material to overheat and cause burns. L L L Only use a compatible charger to charge the batteries. Do not tamper with...