Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
This unit is an additional handset compatible with the following series of Panasonic Digital Cordless Phone: KX-TG1061 You must register this handset with your base unit before it can be used. This installation manual describes only the steps needed to register and begin using the handset. Please read the base unit’s operating instructions for further details. Charge the batteries for about 7 hours before initial use. Please read this installation manual before using the unit and save it for future reference. For assistance, visit our website: for customers in the U.S.A. or Puerto Rico. PNQX1801YA DC1208SY1019 Accessory information Supplied accessories Accessory item/Order number Quantity Charger/PNWETGA106M 1 AC adaptor/PQLV219Z 1 Rechargeable batteries/HHR-4DPA (Part No. HHR-55AAABU or N4DHYYY00004) 2 Handset cover*1/PNYNTGA641TR 1 Belt clip/PNKE1029Z1 1 *1 The handset cover comes attached to the handset. Note: LPlease read the base unit’s operating instructions for additional/ replacement accessories. Setting up Connections (120 V AC, 60 Hz) Hooks Note: LUse only the supplied Panasonic AC adaptor PQLV219. LThe AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.) For assistance, please visit Battery installation/Battery charge Important: LUse the supplied rechargeable batteries. For replacement, we recommend using the Panasonic rechargeable batteries noted on page 2. LWipe the battery ends (S, T) with a dry cloth. LAvoid touching the battery ends (S, T) or the unit contacts. LConfirm correct polarities (S, T). LUSE ONLY Ni-MH batteries AAA (R03) size. LDo NOT use Alkaline/Manganese/Ni-Cd batteries. Charge for about 7 hours. LWhen the batteries are fully charged, the charge indicator goes off. Rechargeable Ni-MH ONLY Confirm “Charging” is displayed. Note: LIf the batteries are fully charged, but the operating time seems to be shorter, clean the battery ends (S, T) and the charge contacts with a dry cloth and charge again. For assistance, please visit Registering a handset to the base unit 1 Handset: Lift the handset and press {OFF}. 2 Base unit: Press and hold {LOCATOR} for about 5 seconds until the registration tone sounds. LIf all registered handsets start ringing, press the same button to stop. Then repeat from step 1. LThe next step must be completed within 90 seconds. 3 Handset: Place the handset on the charger. LContinue the operation even when the handset display shows “Registering”. 4 With the handset still on the charger, wait until a long beep sounds and w stops flashing. Note: LIf an error tone sounds, or if w is still flashing, register the handset according to the base unit’s operating instructions. Display language 1 {MENU} i {#}{1}{1}{0} 2 {V}/{^}: Select the desired setting. 3 Press the middle soft key to save. i {OFF} For assistance, please visit Belt clip NTo attach NTo remove Wall mounting 1 Drive the screws (not supplied) into the wall. 2 Mount the charger (A), then slide it down (B) and to the right (C) until it is secure. 25.4 mm (1 inch) ABC Screws (120 V AC, 60 Hz) For assistance, please visit For your safety To prevent severe injury and loss of life/property, read this section carefully before using the product to ensure proper and safe operation of your product. WARNING Power connection L Completely insert the AC adaptor/power plug into the power outlet. Failure to do so may cause electric shock and/or excessive heat resulting in a fire. L Regularly remove any dust, etc. from the AC adaptor/power plug by pulling it from the power outlet, then wiping with a dry cloth. Accumulated dust may cause an insulation defect from moisture, etc. resulting in a fire. L Unplug the product from power outlets if it emits smoke, an abnormal smell, or makes an unusual noise. These conditions can cause fire or electric shock. Confirm that smoke has stopped emitting and contact the Panasonic Call Center at 1-800-211-PANA (1-800-211-7262). Installation L To prevent the risk of fire or electrical shock, do not expose the product to rain or any type of moisture. L Do not place or use this product near automatically controlled devices such as automatic doors and fire alarms. Radio waves emitted from this product may cause such devices to malfunction resulting in an accident. CAUTION Installation and relocation L The AC adaptor is used as the main disconnect device. Ensure that the AC outlet is installed near the product and is easily accessible. Battery L We recommend using the supplied batteries or additional/replacement batteries noted on page 2 for replacement battery information. USE ONLY rechargeable Ni-MH batteries AAA (R03) size. L Do not mix old and new batteries. L Do not open or mutilate the batteries. Released electrolyte from the batteries is corrosive and may cause burns or injury to the eyes or...