Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
Answering system Problem Cause/solution The unit does not record new messages. R The answering system is turned off. Turn it on (page 38). R The message memory is full. Erase unnecessary messages (page 40). R The recording time is set to “Greeting only”. Change the setting (page 43). R If you subscribe to a voice mail service, messages are recorded by your service provider/telephone company, not your telephone. Change the unit’s number of rings setting or contact your service provider/telephone company (page 43). I cannot operate the R Someone is using the unit. Wait for the other user answering system. to finish. R A caller is leaving a message. Wait for the caller to finish. R The handset is too far from the base unit. Move closer. I cannot operate the answering system remotely. R The remote access code is not set. Set the remote access code (page 41). R You are entering the wrong remote access code. If you have forgotten your remote access code, enter the remote access code setting to check your current code (page 41). R Press each key firmly. R The answering system is turned off. Turn it on (page 42). For assistance, please visit Useful Information Liquid damage Problem Liquid or other form of moisture has entered the handset/base unit. Caution: Cause/solution R Disconnect the AC adaptor and telephone line cord from the base unit. Remove the batteries from the handset and leave to dry for at least 3 days. After the handset/base unit are completely dry, reconnect the AC adaptor and telephone line cord. Insert the batteries and charge fully before use. If the unit does not work properly, contact an authorized service center. R To avoid permanent damage, do not use a microwave oven to speed up the drying process. For assistance, please visit Useful Information FCC and other information equipment complies with Part 68 of the FCC rules and the requirements adopted by ACTA. On the bottom of this equipment label that contains, among other information, a product identifier in the format US:ACJ----------. requested, this number must be provided the telephone company. Registration No.............(found on the bottom of the unit) Ringer Equivalence No. (REN).......0.1BA plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug provided with the product. It is designed be connected to a compatible modular that is also compliant. REN is used to determine the number devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain the number of devices that may be connected to a line, as determined by the RENs, contact the local telephone company. For products approved after July 2001, the REN for the product is part of product identifier that has the format AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). this equipment causes harm to the telephone network, the telephone company notify you in advance that temporary discontinuance of service may be required. if advance notice isn't practical, the telephone company will notify the customer soon as possible. Also, you will be advised of your right to file a complaint with FCC if you believe it is necessary. The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service. If trouble is experienced with this equipment, for repair or warranty information, please contact a Factory Service Center or other Authorized Servicer. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information. If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. This equipment is hearing aid compatible as defined by the FCC in 47 CFR Section 68.316. When you hold the phone to your ear, noise might be heard in your Hearing Aid. Some Hearing Aids are not adequately shielded from external RF (radio frequency) energy. If noise occurs, use an optional headset accessory or the speakerphone option (if applicable) when using this phone. ...