Stimmen - 1, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
1 Press [MENU]. 2 Scroll to “Initial setting” by pressing [d] or [B], then press Select. 3 Scroll to “Set tel line” by pressing [d] or [B], then press Select. 4 Scroll to “Set flash time” by pressing [d] or [B], then press Select. 5 Select the desired time by pressing [d] or [B]. Initial settingBack Select KdBLSet tel line Back Select KdBLSet flash time Back Select KdBLSet flash time :700ms Back Save KdBL Telephone 6 Press Save, then press [OFF]. For assistance, please call: 1-800-211-PANA(7262) 49 Special Features Incoming Call Tone Handset Base Unit During an intercom call (p. 43), you can be informed of incoming calls by two tones. If this feature is turned on, incoming call tones will be heard for as long as the line is ringing. If this feature is set to “2”, incoming call tones will be heard only 2 times. If this feature is turned off, no tones will be heard. The factory preset is “2”. Using the handset, this feature can be set separately for the handset and base unit. Handset incoming call tone Handset 1 Press [MENU]. 2 Scroll to “Ringer setting” by pressing [d] or [B], then press Select. Ringer setting KBack dB Select L 3 Scroll to “Incoming call.” by pressing [d] or [B], then press Select. Incoming call. KBack dB Select L 4 Select “On”, “Off” or “2” by pressing [d] or [B]. Incoming calltone :2 KBackdB Save L 5 Press Save, then press [OFF]. Base unit incoming call tone Handset 1 Press [MENU]. 2 Scroll to “Initial setting” by pressing [d] or [B], then press Select. Initial setting KBack dB Select L 3 Scroll to “Set base unit” by pressing [d] or [B], then press Select. Set base unit KBack dB Select L 4 Scroll to “Incoming call.” by pressing [d] or [B], then press Select. Incoming call. KBack dB Select L 5 Select “On”, “Off” or “2” by pressing [d] or [B]. Incoming calltone :2 KBackdB Save L 6 Press Save, then press [OFF]. Special Features Key Tone Handset You can select whether or not the handset keys will sound tones (key tone, confirmation tone, error tone). The factory preset is ON. 1 Press [MENU]. 2 Scroll to “Initial setting” by pressing [d] or [B], then press Select. 3 Scroll to “Key tone” by pressing [d] or [B], then press Select. 4 Select “Off” or “On” by pressing [d] or [B]. Initial settingBack Select KdBLKey toneBack Select KdBLKey tone:On Back Save KdBL 5 Press Save, then press [OFF]. Re-registering the Handset Handset & Base Unit If “No link to base. Move closer to base, try again.” is displayed even when using the handset near the base unit, the handset may have lost communication with the base unit. You need to re-register the handset to the base unit. • Make sure the base unit is not being used. • Have both the handset and base unit nearby during registration. • Follow steps 1 and 2 listed below. You have about 1 minute to completethem. 1 Base unit: Press and hold [LOCATOR/INTERCOM] until a beep sounds. • The CHARGE indicator flashes. 2 Handset: Press and hold [FLASH/CALL WAIT] until “HandsetRegistering” is displayed. • When registration is complete, a beep sounds from the handset. • Wait for 20 seconds after registration is complete while the handset establishes communication with the base unit. • If the handset beeps 3 times and “Error!!” is displayed, an error occurred. Try again from step 1. • You can stop registration by pressing [OFF] on the handset, and pressing [LOCATOR/INTERCOM] on the base unit. Handset Registering Handset [1] Registered Telephone For assistance, please call: 1-800-211-PANA(7262) 51 Automatic Answering Operation When the unit answers a call, a greeting message is played and the caller’s message is recorded. • The total recording time of all messages (greeting, incoming and memo) is about 16 minutes. If messages are recorded in noisy rooms, the time may be shortened by up to 3 minutes. • To select the caller’s recording time, see page 22. • A maximum of 64 messages (including greeting and memo message) can be recorded. Setting the Unit to Answer Calls Base Unit Press [ANSWER ON] to turn on the Answering System. • The indicator lights and the unit announces “Answer set” and current day and time. If “Answer set. Set time” is heard, set the date and time (p. 14). • The unit will announce the remaining recording time if it is less than 3 minutes. • When no recording time is available, you will need to erase any unnecessary messages before new messages can be recorded (p. 57). The unit can indicate that memory is full in the following ways: —“ FULL ” will flash on the base unit and the ANSWER ON indicator will flash rapidly until you erase a message. [ANSWER ON] and Indicator — The unit will announce “Memory full” when you press [ANSWER ON], [GREETING REC], or [MEMO], and after playing back messages or recording a message. • If you do not want the unit to answer calls, press [ANSWER ON] again to turn off the Answering System. The indicator light goes out and “Answer off” is heard. • You can also turn on the Answering System remotely from an outside phone (p. 62). • If...