Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
Restart from step 1. If a power failure occurs, the setting will return to the factory preset (700 ms). Reprogram if necessary. 40 For Call Waiting Service Users Press [CALL WAIT I if you hear a call-waiting tone while talking. ® The first call is put on hold and you can answer the second call, o TO return to the first caller, press (CALL WAIT] again. • You can also press [FLASH] instead of [CALL WAIT I. © The call waiting service is not available when the parallel connected telephone is in use. • If this function does not operate properly, the flash time (call waiting time) may not be set correctly. Consult with your telephone company for details. See page 40 on how to adjust the time. Visual Call Waiting (Call Waiting ID) Service Visual Call Waiting (Call Waiting ID) Service allows your handset to display the second caller’s information. After you hear a call-waiting tone while talking, the handset will display the caller’s name with the phone number and “----waiting---- © Please contact your telephone company for details and availability in your area. Temporary Tone Dialing (For Rotary or Pulse Service Users) Press iTONEl before entering access numbers which require tone dialing. • The dialing mode changes to tone. You can enter numbers to access an answering service, electronic banking service, etc. When you hang up, the mode will return to pulse. • Access numbers entered after pressing [TONE] will not be included when redialing. How to Use the PAUSE Button (For Analog PBX Line/Long Distance Service Users) We recommend you press [ REDIAL/PAUSE I if a pause is required for dialing with a PBX or to access a long distance service. Ex. Line access number (9) (PBX) d] IREDIAL/PAUSEl ts> [Phonenumber] o Pressing [REDIAL/PAUSE] once creates a 3.5 second pause. This prevents misdialing when you redial or dial a stored number. • Pressing I REDIAL/PAUSEl more than once increases the length of the pause between numbers. NANCY BROWN 1-000-222-3333 ----Waiting---- Battery Replacement If “Recharge” is displayed and/or “ { I ] ” flashes after being fully charged, replace the battery with a new Panasonic P-P501 (KX-A36) battery. To order, call the accessories telephone number on page 2. To prevent memory loss, replace within 3 minutes. 1 Remove the cover by sliding it while pressing the arrow. Replace the battery, then close the cover. Be sure to charge the new battery for about 4 hours in order to display the battery strength prompt correctly (p. 12). Attention: The product you have purchased is powered by a nickel cadmium battery which is recyclable. At the end of its useful life, under various state and local laws, it is illegal to dispose of this battery into your municipal waste stream. Please call 1-800-8-BATTERY for information on how to recycle this battery. 42 Adding Another Phone This unit will not function during a power failure. To connect a standard telephone on the same line, use the Panasonic T-adaptor KX-J66. To order, call the accessories telephone number on page 2. 43 Before Requesting Help Problem Remedy “Out of range” is displayed and an alarm tone sounds when vou Dress (TALK). • You are too far from the base unit. Move closer and try again. • Place the handset on the base unit and try again. • Plug in the AC adaptor. • Raise the base unit antenna. The unit does not work. • Check the settings (p. 11-20). • Charge the battery fully (p. 12). • Clean the charge contacts and charge again (p. 13). • Install the battery properly (p. 42). • Place the handset on the base unit and unplug the AC adaptor to reset. Plug in, then try again. • Re-install the handset battery within 3 minutes to avoid memory loss and place the handset on the base unit. Then try again. Static, sound cuts in/out, fades. Interference from other electrical units. • Locate the handset and the base unit away from other electrical appliances (p. 3). ° Move closer to the base unit. • Raise the base unit antenna. • Press ICH) to select a clearer channel. The handset does not ring. • The ringer volume is set to OFF. Press iRINGERl while the TALK indicator light is off (p. 19). The handset display is blank. • The handset is in the stand-by mode (p. 13). Press SEARCH 0 or @ to turn the display on. 44 Problem Remedy The handset display is stilt blank after pressing SEARCH 0 or @. ® Charge the battery fully (p. 12). You cannot program items, such as the dialing mode. * Programming is not available while the unit is in the talk mode or when viewing caller information. o Do not pause for over 60 seconds while programming. • SEARCH 0 or 0 may have been pressed when you picked up the handset. Press (EXlTl, then trv aaain. You cannot store a phone number in memory. • You cannot store a number while the unit is in the talk mode. • Do not pause for over 60 seconds while storing. While programming or searching, the unit starts to ring and stops the program/search. ® To answer the call. Dress iTALKl. St...