Stimmen - 4, Durchschnittliche Bewertung: 4.8
(
)
)
|
Anleitung Zusammenfassung
All rights reserved. Printed in Mexico. 848233037 Issue 1AT&T aaaaaaaaaaaaa0 aaaaaaaaaaaa0 INSTALLATION Standard AC Outlet Modular Wall Jack AC Adapter Power Cord Telephone Line Cord 1 Insert the microcassette. Lift the cover and insert the 4 Set the Handset Ringer ON/OFF switch. Plug the other end of the line cord into a modular phone jack. Make 2 microcassette with the full reel to the right. Choose a spot near an electrical outlet and a telephone jack. Set the switch on the side of the handset to ON so the handset will ring. When this switch is set to OFF the handset will not ring. 6 sure the plug snaps firmly in place. Mount the base on the wall. (WALL MOUNTING ONLY) Hold the base so that the mounting • This phone requires a modular NOTE: If you set the Ringer ON/OFF knobs on the standard wall jack will telephone jack and a standard switch to OFF, the handset battery will last fit into the holes on the bottom of electrical outlet (120v AC). longer. However, when the ringer is set to the base. Slide the base down onto 3 Install the handset battery. (For an illustration of battery OFF, you will always need to press P to answer a call, even when the handset has been in the base. 7 the knobs until it locks into place. Connect the power cord. installation, see “BATTERIES.”) • Plug the battery pack connector 5 Connect the telephone line cord. Plug the power cord into the jack labeled POWER on the back of the into the handset and place the Plug one end of the telephone line base. Plug the AC adapter on the battery pack into the case, so the cord into the jack on the back of the power cord into an electrical outlet. wires rest above the battery base. (If you are wall mounting the The microcassette will automatically pack. phone, wrap the excess cord in the rewind. When the tape stops moving, • Place the battery case cover on groove on the bottom of the base.) the light above the Pbutton the handset by sliding it on its track up over the battery case until it snaps firmly in place. 1 aaaaaaaaaaaaa0 aaaaaaaaaaaa0 INSTALLATION CHARGINGHANDSET IN USE MEMO/REWIND FAST FWD SAVE CLOCK PLAY/STOP VOLUMEUse with other buttons to change settings. Base Antenna (extended) Record or play outgoing announcement. Cover Turn system on or off. Lift panel door to access features (see figure at right). Audible clock; also use with CHANGE to set time/day. Adjust message playback volume. Fast forward during message playback. Play messages or stop message playback. Save messages. should be on steadily. If the light is 8 flashing rapidly, the microcassette is not installed properly. Remove the cassette, and check to see if it's damaged. If it's okay, install it again. After you have installed the cassette, press Pto reset the system. CAUTION: Use only the power 9 supply provided with this product. To obtain a replacement, call 1 800 722–9125. Power Supply DAS-2. Input: 120V, 60Hz, 15W. Output: 9V AC, 780 mA. Charge the handset batteries before use. Place the handset face down in the base. The CHARGING light on the base goes on to show the handset is in the right position to charge the batteries. The batteries will be fully charged in 14 hours. Check for dial tone. Make sure the base antenna is upright. After the batteries are charged, pick up the handset and check for dial tone by pressing P; the PHONE light should go on and you should hear a dial tone. Press P to hang up. 10 Set the dial mode. If you have touch tone service, the phone will be ready to use as soon as the battery is charged. If you have dial pulse service, you’ll need to set the dial mode. Press P (wait for dial tone), p, #, #, #, 3. To return to touch tone dialing with touch tone service, when the phone is off, press P (wait for dial tone), p, #, #, #, 8. IMPORTANT: After you have installed the phone, you will need to record an announcement that callers will hear when the system answers. Please see the Answering System Operation section of this manual. 2 aaaaaaaaaaaaaaaaaa0 aaaaaaaaaaaaaaaaaa0 BATTERIES Charging the Handset Battery Pack The batteries need charging when: • The phone beeps four times when you press P. • The LOW BATTERY light on the handset flashes on and off. • The phone does not respond when you press P, and no lights go on. Place the handset in the base so the CHARGING light goes on. The batteries will be fully charged in 14 hours. NOTE: The handset must lie flat in the base, with the keypad facing down, when charging. The charging light in the base goes on if the handset is positioned correctly. A fully charged battery maintains standby power for up to 14 days when the Handset Ringer ON/OFF switch is set to ON, and up to 21 days when the Handset Ringer ON/OFF switch is set to OFF. If it’s more convenient for you, you can leave the handset in the base all the time. It is impossible to overcharge the batteries. If you get a low battery indicator even after the batteries have been charged 14 hours, the battery should be replaced. CAUTION: To reduce the r...