Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Make sure the base is at least 1 metre away from other electrical appliances to avoid interference. Handset range The BT Elements phone has a range of up to 1000 metres outdoors when there is a clear line of sight between the base and the handset. When there is no clear line of sight between the base and the handset, e.g. the base is indoors and the handset either indoors or outdoors, the range could be reduced to 50 metres. Thick stone walls can severely affect the range. Signal strength The icon on your handset indicates when you are in range. When you move out of range of the base, the out of range tone will sound every minute and the icon will flash on the handset display. This is repeated until you move back into range. Talk/Standby time In ideal conditions, fully charged handset batteries should give about 10 hours talk time or 100 hours standby time on a single charge. The base must remain plugged in to the mains and switched on at all times. Please note that if you are using the torch feature, the talk/standby times will be reduced. Note that new batteries do not reach full capacity until they have been in normal use for several days. Battery low warning If the symbol flashes in the display and you hear a warning beep every minute, you will need to recharge the handset before you can use it again. During charging, the symbol will scroll in the display. Battery performance To keep your batteries in the best condition, leave the handset off the base for a few hours at a time. Running the batteries right down at least once a week will help them last as long as possible. From a rundown state the handset may take a minute or so to power up the display. The charge capacity of rechargeable batteries will reduce with time as they wear out, giving the handset less talk/standby time. Eventually they will need to be replaced. New batteries are available from the BT Elements Helpline on 0870 605 8047. If you experience any problems, please call the Helpline on 0870 605 8047 or email bt.helpdesk@suncorptech.com Elements Additional Handset – New Style – Edition 2 – 31.08.06 – 7780 Getting started After charging your handset for the first time, subsequent charging time is about 6–8 hours a day dependant on usage. Batteries and handset may become warm during charging. This is normal. Setting up 1. At the handset: Make sure the battery ribbon is laying flat inside the battery compartment and insert the 2 x AAA NiMH rechargeable batteries supplied observing the polarity markings (+ and -). 2. Replace the battery cover: hook the two plastic clips into place first, then lower and screw the cover into place. Finally, screw the belt clip on. You can use a coin, e.g. 10p piece if you don’t have a screwdriver. If you experience any problems, please call the Helpline on 0870 605 8047 or email bt.helpdesk@suncorptech.com Elements Additional Handset – New Style – Edition 2 – 31.08.06 – 7780 Getting started 3. At the charger: Plug the charger power cord into the charger and the mains power wall socket. Place the handset on the base to charge for at least 24 hours. The red Charging light comes on. While the handset is charging, the symbol scrolls in the display, when the handset is fully charged the display shows the symbol. Registering your handset to your BT Elements base If you are registering the handset to another DECT GAP compatible base station that is not a BT Elements, please refer to the user guide for that base for registration instructions. IMPORTANT DECT GAP Profile only guarantees that basic calling functions will work correctly between different makes/types of handset and base. There’s a possibility that certain services such as Caller Display will not work correctly. The extended range feature only applies when registered to a BT Elements base. IMPORTANT Before registration, make sure the handset batteries are fully charged and that you are close to the main base unit. At the BT Elements base: 1. Press and hold until you hear a beep, then release it. The base will now remain in registration mode for 90 seconds, during which time you will need to complete the following procedure. At the BT Elements additional handset: 2. Press to open the main menu. Menu 3. Press or until Register is displayed, then press Menu . 4. Press or to highlight Reg Base and press Menu. 5. Enter a base number (from 1 to 4) and press Menu. If you experience any problems, please call the Helpline on 0870 605 8047 or email bt.helpdesk@suncorptech.com Elements Additional Handset – New Style – Edition 2 – 31.08.06 – 7780 Getting started 6. Enter the 4 digit PIN code of the base station you are registering to (BT Elements base default 0000) and press . Menu When the base is located, your handset will display the base ID Menunumber, press to confirm registration to this base or cancel by pressing . The handset is automatically allocated the next available handset number which is displayed when in standby mode. If registration is unsuccessful, th...