Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
After tuning into a station, the search stops. • The search may not stop at a station with a very weak signal. Presetting Stations The unit can store a total of 20 stations in memory (10FM, 10AM). Presetting allows you to tune in to a station directly. 1. Tune in to a desired station. 2. Press the /MEMORY button. The preset number will blink and the "MEM" indicator will be shown on the display. 3. Press the PRESET/SNOOZE button to select the preset number. 4. Press the /MEMORY button again to store it in memory. 5. Repeat steps 1-4 to store other stations. Tuning in to a Preset Station 1. Press the PRESET/SNOOZE button, the preset number and "MEM" will be shown on the display. 2. Press the PRESET/SNOOZE button repeatedly to select the preset number for your desired station. For Better Reception FM: Fully unwind the antenna wire. Extend the antenna wire and place it in the position that sounds best. Note: Do not connect the FM antenna to an outside antenna. When the reception is good, the "STEREO" indicator will appear on the display. AM: Reposition the unit to get better AM reception. Note: To prevent possible interference to the AM signal, please keep a certain distance(The AC adaptor cable's length) away from the main unit. - LISTENING TO YOUR iPOD DUAL ALARM SETTING SPECIFICATIONS The unit should be in STANDBY mode to set alarm. iPod Compatibility DC: 12V 1.25A EXTERNAL DC SUPPLY The unit works with iPod mini (4GB, 6GB), iPod nano (1st generation) -1GB, 2GB, 4GB, iPod 5th BACKUP BATTERIES FOR CLOCK: 2x1.5V UM-4 OR AAA SIZE • The alarm can be set to activate twice a day by setting two different alarm times in ALARM1 and generation (video) -30GB, 60GB, 80GB, iPod nano (2nd generation) -2GB, 4GB, 8GB, iPod classic ALARM2. RADIO FREQUENCY: AM 520 ~ 1710KHz(80GB, 160GB), iPod nano 3rd generation (video) -4GB, 8GB and iPod touch (8GB, 16GB, 32GB). HOUR digits MINUTE digits • The unit can be set to “Buzzer”, “Radio” or “iPod” alarm. FM 87.5 ~ 108.0MHz Design and specifications are subject to change without notice. To Set Alarm 1 Other iPod models(and other audio devices) are supported through the AUX IN jack on the unit back 1. Press the ALARM1 button, the “ ” icon blinks on the display. iPod Dock Adaptor 2. Press the ALARM1 button once again, then the “ ” icon, hour Before connecting your iPod, you need to install the appropriate iPod Dock Adaptor in the dock of & minute digits blink on the display. LIMITED WARRANTY the unit. Four iPod Dock Adaptors are included as shown below(if the adaptor is not supplied in the panel (see AUX IN CONNECTION section). 3. Press the HOUR/ button to adjust the hours. ALARM1 indicator ALARM2 indicator VENTURER ELECTRONICS (“VENTURER”) makes the following limited warranty. This limited warranty accessory, please use the adaptor that comes with your iPod.): 4. Press the MIN/ button to adjust the minutes. extend to the original consumer purchaser and is limited to non-commercial use of the product. Installing the iPod Dock Adaptor 1. Choose the iPod Dock Adaptor that fits your iPod (if the adaptor is not supplied in the accessory, please use the adaptor that comes with your iPod). 2. Lift up the iPod Dock flap door to approximately 90o . Removing the iPod Dock Adaptor Remove the Dock Adaptor by gripping the inside with your thumb, then lifting out the adaptor using the friction between your thumb and the adaptor. 5. Press the FUNCTION/ button to select “Buzzer”, “FM”, “AM”, “iPod”. 6. Adjust the volume control to obtain the desired volume for the Alarm1. 7. Press the ALARM1 button again to confirm. 8. The Alarm 1 indicator will light up. 3. Insert your iPod Dock Adaptor into the dock until it sits firmly in place. Inserting Your iPod 1. Ensure the appropriate iPod Docking Adaptor is installed. PRESET EQ This system supports a variety of equalizers and sound effects. During playback, press the PRESET EQ button on the remote control to select a desired music mode. Each time the PRESET EQ button is pressed, the music mode will be changed to the next one as follows: -> (ROCK) -> -> (CLASSIC) The sleep timer automatically turns the unit off after a certain time. 1. While the unit is on, press the SLEEP button-the display will indicate “90”. 2. Press the SLEEP button repeatedly to select the desired sleep time as below: 3. After setting a desired sleep time, the “ ” icon will be shown on the display. 4. The unit will automatically turn off once it counts down the sleep time. • To clear the preset sleep time, keep pressing the SLEEP button until “00” is shown. The “ ” icon disappears. Note: For the “Radio” Alarm, you should tune into your desired radio station before setting alarms-the alarm will turn on to the last station you tuned. The clock radio will wake up to “Buzzer”, “Radio”, “iPod”, when alarm timer reaches the preset time and then turns off automatically after 60 minutes. TO CHANGE THE ALARM TIME Set the alarm time again. TO SET ALARM 2 Setting the alarm for Alarm2 is the same a...